Toyota Previa Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(20)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(20)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Toyota Previa Water Pump Replacement is $372 with $190 for parts and $182 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1992 Toyota PreviaL4-2.4LService typeWater Pump ReplacementEstimate$582.18Shop/Dealer Price$682.03 - $971.05
1991 Toyota PreviaL4-2.4LService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.02 - $955.32
1993 Toyota PreviaL4-2.4LService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.05 - $955.38
1995 Toyota PreviaL4-2.4LService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.05 - $955.37
1997 Toyota PreviaL4-2.4L TurboService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$669.97 - $958.73
1994 Toyota PreviaL4-2.4LService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.23 - $955.69
1995 Toyota PreviaL4-2.4L TurboService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.07 - $955.41
1994 Toyota PreviaL4-2.4L TurboService typeWater Pump ReplacementEstimate$570.47Shop/Dealer Price$668.05 - $955.37
Show example Toyota Previa Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Toyota mechanics

Real customer reviews from Toyota owners like you.

Excellent Rating

(20)

Rating Summary
19
1
0
0
0
19
1
0
0
0

Victor

36 years of experience
230 reviews
Victor
36 years of experience
Toyota Previa L4-2.4L - Brake System Flush - Albuquerque, New Mexico
He was both knowledgeable and friendly. Would recommend him for the job

Robert

21 years of experience
1307 reviews
Robert
21 years of experience
Toyota Previa L4-2.4L - Car is stalling - Broomfield, Colorado
Robert did a great job and he was friendly

John

33 years of experience
1126 reviews
John
33 years of experience
Toyota Previa L4-2.4L - Exhaust Gas Recirculation/EGR Valve - League City, Texas
100% satisfied. John did a geat job in very tough conditions (it was very hot and humid!)

Jerome

35 years of experience
206 reviews
Jerome
35 years of experience
Toyota Previa L4-2.4L - Car is not starting - Silver Spring, Maryland
It was a very good service/inspection work done for my car. Thanks

Excellent Rating

(20)

Rating Summary
19
1
0
0
0
19
1
0
0
0
Number of Toyota Previa services completed
220+
services done by our mechanics
TOTAL NUMBER OF EXPERT Toyota MECHANICS
1700+
experts on our platform

Recent articles & questions

P0111 OBD-II Trouble Code: IAT sensor circuit range or performance problem
P0111 P0111 code definition Intake Air Temperature (IAT) sensor circuit range or performance problem What the P0111 code means P0111 is the OBD-II generic code that indicates the engine control module (ECM) has recorded the IAT sensor input go out...
How to Buy a Good Quality Truck Tool Box
If If you have a pickup truck, the bed offers the means to carry a wide range of cargo. However, you can also turn it into a portable tool shed with the right truck tool box. There are quite a...
B1909 OBD-II Trouble Code: Air Bag Crash Sensor #2 Ground Circuit Short to Ground
B1909 means there is a malfunction with the #2 airbag crash sensor circuit, most likely because of a bad electrical component or faulty sensor.

Car sounds like lawn mower when pressing the gas pedal

Hello. It sounds like you have a large exhaust leak. If there is an exhaust leak, you are getting raw exhaust out of the engine, and that might be what you're smelling. You should not operate or drive the vehicle...

My car stalled, I checked the oil and it was low. I added 2 quarts and barely made it 4 blocks. There is no pressure when pressing the gas.

This may or may not be related to the low oil level (https://www.yourmechanic.com/services/oil-level-is-low-inspection). If the car was overheated and potentially has developed a blown head gasket, this may be possibly what have caused the stall. When this happens, the cylinder...

Can't get power at all. Misfire with code P0303.

Hi there. The code P0303 (https://www.yourmechanic.com/article/p0303-obd-ii-trouble-code-cylinder-3-misfire-detected-by-spencer-clayton_2) means that cylinder number 3 has a misfire. There are three ways that the cylinder number 3 can be misfiring. Spark plug is fouled out and not creating a strong enough spark to ignite...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com