Toyota Land Cruiser Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(14)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(14)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Toyota Land Cruiser Brake Pad Replacement is $198 with $58 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2019 Toyota Land CruiserV8-5.7LService typeBrake Pads - Front ReplacementEstimate$326.14Shop/Dealer Price$372.53 - $503.58
2010 Toyota Land CruiserV8-5.7LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.22 - $471.44
2008 Toyota Land CruiserV8-5.7LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.25 - $471.48
2010 Toyota Land CruiserV8-5.7LService typeBrake Pads - Rear ReplacementEstimate$307.11Shop/Dealer Price$349.25 - $471.48
1997 Toyota Land CruiserL6-4.5LService typeBrake Pads - Rear ReplacementEstimate$307.11Shop/Dealer Price$350.72 - $474.06
2011 Toyota Land CruiserV8-5.7LService typeBrake Pads - Rear ReplacementEstimate$307.11Shop/Dealer Price$349.39 - $471.73
2016 Toyota Land CruiserV8-5.7LService typeBrake Pads - Rear ReplacementEstimate$307.11Shop/Dealer Price$349.26 - $471.51
2017 Toyota Land CruiserV8-5.7LService typeBrake Pads - Rear ReplacementEstimate$317.13Shop/Dealer Price$361.77 - $491.52
Show example Toyota Land Cruiser Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Toyota mechanics

Real customer reviews from Toyota owners like you.

Excellent Rating

(14)

Rating Summary
13
0
1
0
0
13
0
1
0
0

AL

8 years of experience
232 reviews
AL
8 years of experience
Land Cruiser 1996 - Brake Pads - Happy Valley, OR
Great service. On time job well done

Jose

6 years of experience
63 reviews
Jose
6 years of experience
Land Cruiser 1995 - Brake Rotor/Disc - San Bruno, CA
Was in bad need of rear brakes, Jose for me all fixed and after a test drive my brakes are quiet and working strong again!!

Jose

6 years of experience
63 reviews
Jose
6 years of experience
Land Cruiser 1995 - Brake Shoes (Rear) - San Bruno, CA
Was in bad need of rear brakes, Jose for me all fixed and after a test drive my brakes are quiet and working strong again!!

Derrick

5 years of experience
124 reviews
Derrick
5 years of experience
Land Cruiser 1999 - Valve Cover Gasket - Walnut Creek, CA
Derrick was on time and performed the service with complete professionalism. He discussed other issues he noticed with my car. Would certainly recommend him and request him again.

Excellent Rating

(14)

Rating Summary
13
0
1
0
0
13
0
1
0
0
Number of Toyota Land Cruiser Brake Pad Replacement services completed
154+
services done by our mechanics
TOTAL NUMBER OF EXPERT Toyota MECHANICS
1700+
experts on our platform

Recent articles & questions

How Much Does a Mechanic Make in Iowa?
Automotive technician jobs in Iowa have an mean salary of $39k, with some mechanics earning as much as $40k.
How Long Does a Ball Joint Rear Last?
Common signs include clunking noises and tire wear in the rear, and you may start steering to the right or left unintentionally.
P2568 OBD-II Trouble Code: Direct O-Zone Reduction Catalyst Temperature Sensor Circuit Range/Performance
P2568 P2568 code definition Direct O-zone Reduction Catalyst Temperature Sensor Circuit Range/Performance What the P2568 code means P2568 is an OBD-II generic code that the engine control module (ECM) has detected the engine o-zone reduction catalyst temperature sensor to be...

Trunk popping open while driving

It sounds like you are on the right track. The most common cause would be an issue with the locking assembly but if the car is equipped with a switch to open the trunk that could also be an issue....

Car is making a hissing noise during acceleration.

Hi There, There are many things that could be caused by this, however a a common symptom of a vacuum leak is a hissing that will become more noticeable during acceleration as you describe. High idle speeds or in some...

I have a 2015 Dodge charger 3.6. I was sitting at a Walgreens for an extended period of time while the car was in park and did not realize that my foot remained on the [brake](/topics-brake-dodge/) during this time. When I went to leave the vehicle I pushed the button to turn it off and then took my foot off of the brake. Close the door went into the store came back out and I cannot press the breakdown. in order to start the car with the push button you have to press the brake and push the button but I am unable to press the brake. I'm guessing that pushing the brake in has allowed hydraulic fluid to build up and now I have no give in the braking system. Is there some sort of release valve so that I can unscrew and allow the pressure to alleviate the system or is there another way to fix this?

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com