Pontiac Sunbird Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Pontiac Sunbird Brake Drum Replacement is $355 with $184 for parts and $171 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1988 Pontiac SunbirdL4-2.0LService typeBrake Drum ReplacementEstimate$655.46Shop/Dealer Price$772.45 - $1067.19
1991 Pontiac SunbirdV6-3.1LService typeBrake Drum ReplacementEstimate$539.90Shop/Dealer Price$650.17 - $940.38
1990 Pontiac SunbirdL4-2.0L TurboService typeBrake Drum ReplacementEstimate$539.90Shop/Dealer Price$650.16 - $940.38
1977 Pontiac SunbirdV6-3.8LService typeBrake Drum ReplacementEstimate$625.16Shop/Dealer Price$748.44 - $1064.32
1978 Pontiac SunbirdV8-5.0LService typeBrake Drum ReplacementEstimate$625.16Shop/Dealer Price$748.53 - $1064.48
1989 Pontiac SunbirdL4-2.0L TurboService typeBrake Drum ReplacementEstimate$605.46Shop/Dealer Price$722.49 - $1017.26
1986 Pontiac SunbirdL4-1.8L TurboService typeBrake Drum ReplacementEstimate$617.96Shop/Dealer Price$734.65 - $1029.17
1992 Pontiac SunbirdL4-2.0LService typeBrake Drum ReplacementEstimate$558.90Shop/Dealer Price$670.61 - $961.92
Show example Pontiac Sunbird Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Pontiac mechanics

Real customer reviews from Pontiac owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Paul

10 years of experience
38 reviews
Paul
10 years of experience
Pontiac Sunbird L4-2.0L - Ignition Lock Assembly - Austin, Texas

Michael

40 years of experience
131 reviews
Michael
40 years of experience
Pontiac Sunbird L4-2.0L - Car is overheating - Columbus, Ohio
Michael was very professional, kind, courteous, attentive. He listened to what I had to say and helped to find the solution to the problem. Thank you, Mike, for everything you did to get me back on the road. 

Joshua

27 years of experience
709 reviews
Joshua
27 years of experience
Pontiac Sunbird L4-2.0L - Ignition key does not turn - Oakland, California
Joshua was great. He arrived early which was a plus. He quickly resolved the problem and ordered the parts. I would recommend him to everyone. As a matter of fact while he was there attending my Mom's car, I had him to look at my car as well. He was wonderful and very professional.

Andrew

11 years of experience
867 reviews
Andrew
11 years of experience
Pontiac Sunbird L4-2.0L - Axle / CV Shaft Assembly Replacement (Driver Side Front) - Kansas City, Missouri
Very good experience with this service, Andrew was a true life saver. Will definitely be using this service again. I will definitely recommend this service to everyone that needs or could use it. Thank you

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Pontiac Sunbird services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Pontiac MECHANICS
800+
experts on our platform

Recent articles & questions

The Best Used Cars to Buy If You Live in a Hilly Area
Do Do you live in terrain that is hilly? Do your city streets feature plenty of inclines and declines that can be nothing short of treacherous in miserable weather? If so, when it’s time to purchase a car you’re looking...
The Guide to Legal Car Modifications in Maine
ARENA Creative / Shutterstock.com Maine has a variety of vehicle modification laws. If you live in the state or are planning to move there, understanding the following regulations will help ensure that your modified car or truck...
P0821 OBD-II Trouble Code: Gear Lever X Position Circuit
P0821 code means that a defect in the transmission shift mechanism range circuit has been detected due to a failed sensor or a locked solenoid.

What Types of Trouble Codes Cause Lights to Come On in My Dash?

Different vehicles have a different number of lights on the dashboard to warn you of problems, some with just a few basic lights while others have plenty to distinguish between different issues. This article will cover just the bright yellow...

Check engine Light on and medium consume increased fast

Hello, According to the numbers you have provided, the engine is consuming much more fuel than it is supposed to. You also mention that this began only after your Check Engine Light (https://www.yourmechanic.com/article/the-check-engine-light-demystified) came on. From your description, it appears...

I have no tail lights but all other lights work

Hey there. You should check to see if you have front parking lights. If the front parking lights work, then the rear parking lights will have bad bulbs or sockets for the bulbs. The front and rear parking lights are...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com