Mercedes-Benz G550 Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(7)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(7)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Mercedes-Benz G550 Water Pump Replacement is $430 with $269 for parts and $161 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2016 Mercedes-Benz G550V8-4.0L TurboService typeWater Pump ReplacementEstimate$1472.70Shop/Dealer Price$1753.17 - $2287.40
2010 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1062.66Shop/Dealer Price$1303.47 - $1868.10
2011 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1062.66Shop/Dealer Price$1303.46 - $1868.08
2014 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1005.67Shop/Dealer Price$1235.81 - $1792.44
2017 Mercedes-Benz G550V8-4.0L TurboService typeWater Pump ReplacementEstimate$1316.70Shop/Dealer Price$1538.91 - $2029.44
2012 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1062.66Shop/Dealer Price$1303.46 - $1868.08
2009 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1082.66Shop/Dealer Price$1322.51 - $1886.41
2015 Mercedes-Benz G550V8-5.5LService typeWater Pump ReplacementEstimate$1042.11Shop/Dealer Price$1278.65 - $1851.02
Show example Mercedes-Benz G550 Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0

Tabitha

17 years of experience
314 reviews
Tabitha
17 years of experience
Mercedes-Benz G550 V8-5.5L - Headlight Bulb Replacement (Driver Side Low Beam) - La Jolla, California
very knowledgable, patient and good comunicator., detailed explanations.

Jason

32 years of experience
500 reviews
Jason
32 years of experience
Mercedes-Benz G550 V8-5.5L - Car is not starting - Saratoga, California
Jason is very knowledgeable and great at what he does. He is punctual and very friendly. I highly recommend him for any type of car service.

Nazareth

27 years of experience
266 reviews
Nazareth
27 years of experience
Mercedes-Benz G550 V8-5.5L - Oil Change - Pasadena, California
Nazareth is an exceptionally competent and nice person, It was a pleasure to deal with. Highly recommending his service.

Sergio

10 years of experience
204 reviews
Sergio
10 years of experience
Mercedes-Benz G550 V8-5.5L - Pre-purchase Car Inspection - San Antonio, Texas
Sergio was responsive and on-time. He was also very throughout with his inspection.

Excellent Rating

(7)

Rating Summary
7
0
0
0
0
7
0
0
0
0
Number of Mercedes-Benz G550 services completed
77+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1000+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Nissan Maxima
The The Maxima is one of the most popular vehicles from Nissan, and they’ve been hitting it out of the park in recent years. The 2012 Nissan Maxima is a fantastic, practical vehicle that offers some excellent performance for a...
P2018 OBD-II Trouble Code: Throttle Actuator Control Module Performance
P2108 P2108 code definition Throttle actuator control module performance What the P2108 code means This trouble code indicates that the powertrain control module has detected a malfunction with the throttle body control motor or module. This code is only found...
How to Safely Park on a Hill
While While parking a car is an essential driving skill that must be proven to gain a license, parking on a hill is a skill not everyone possesses. Although drivers may not have to demonstrate this ability, it is crucial...

vdc slip light comes on, car goes in limp mode nissan altima 2011

Hi There, The VDC and slip lights could potentially indicate the vehicle may be low on brake fluid or the brake pads (https://www.yourmechanic.com/services/brake-pads-replacement) may be worn resulting in the brake fluid to read lower. The low brake fluid may also...

I have a 2007 Ford Focus. The serpentine belt broke causing my check engine light to come on as well as my battery light.

You will have to have the computer scanned to get the codes stored to see if there is only codes pertaining to the low voltage condition and have codes cleared using the scanner and then see what codes return. If...

Rethreaded my spark plug and may have dropped some small metal shavings in the plug hole is there a way to get them out

The only thing you can do to get out the metal shavings from the cylinder without removing the cylinder head is to use a long air hose pressure probe into spark plug hole and blow air into cylinder to try...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com