Mercedes-Benz C280 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz C280 Brake Drum Replacement is $318 with $156 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
2000 Mercedes-Benz C280V6-2.8L	Service typeBrake Drum Replacement	Estimate$574.86	Shop/Dealer Price$699.46 - $1006.31
1997 Mercedes-Benz C280L6-2.8L	Service typeBrake Drum Replacement	Estimate$474.36	Shop/Dealer Price$582.39 - $839.41
1995 Mercedes-Benz C280L6-2.8L	Service typeBrake Drum Replacement	Estimate$578.24	Shop/Dealer Price$712.24 - $1047.16
1996 Mercedes-Benz C280L6-2.8L	Service typeBrake Drum Replacement	Estimate$474.36	Shop/Dealer Price$582.32 - $839.28
1994 Mercedes-Benz C280L6-2.8L	Service typeBrake Drum Replacement	Estimate$578.24	Shop/Dealer Price$712.28 - $1047.24
2007 Mercedes-Benz C280V6-3.0L	Service typeBrake Drum Replacement	Estimate$541.76	Shop/Dealer Price$666.64 - $974.20
1999 Mercedes-Benz C280V6-2.8L	Service typeBrake Drum Replacement	Estimate$549.36	Shop/Dealer Price$673.61 - $980.19
1998 Mercedes-Benz C280V6-2.8L	Service typeBrake Drum Replacement	Estimate$549.36	Shop/Dealer Price$674.71 - $982.13

Show example Mercedes-Benz C280 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(77)

Rating Summary

73

3

1

0

0

73

3

1

0

0

SEE REVIEWS NEAR ME

Tien

23 years of experience

903 reviews

Tien

23 years of experience

by Nelson

Mercedes-Benz C280 L6-2.8L - Spark Plugs - Oakland, California

This is my second appt with Tien and was just as impressed as the first. Professional thorough and goes the extra mile without you asked

Peter

28 years of experience

529 reviews

Peter

28 years of experience

by Jonathan

Mercedes-Benz C280 L6-2.8L - Fuel Pump - North Hills, California

He got the job done fast and effective, I definitely recommend him

Rohon

48 years of experience

73 reviews

Rohon

48 years of experience

by YOVAN

Mercedes-Benz C280 V6-3.0L - Car Battery Replacement - Howard Beach, New York

Excellent service from a quality mechanic. Thank you

Tien

23 years of experience

903 reviews

Tien

23 years of experience

by Ben

Mercedes-Benz C280 V6-2.8L - Oil Change - Berkeley, California

Tien was great, but the app/business made two errors. A. You switched mechanics on me at 9pm the night before. Tien was unaware of this switch and couldn't make it to my house in time when he found out the next morning. I understand you expect your mechanics to be responsive, but that's unrealistic...consequently the customer paid for it. B. A customer support rep reached out, with what I believe is an automated email, asking why I signed up but did not book an appointment. I had booked an appointment; this showed disorganization and hurt brand equity. All-in-all if Tien hadn't been awesome, quick, courteous my experience would have been very different. Positives: Very convenient service. I feel it should be cheaper with the reduced overhead of a mechanic shop, but with discount was very fair. Effective and quick, no hassle. Negatives: Y'all need a redesign on web. Haven't seen app, but web is kinda 2005-ish. Thanks for the oil change and I'll recommend y'all (and Tien) to some folks. Live long and prosper.

Excellent Rating

(77)

Rating Summary

73

3

1

0

0

73

3

1

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

2012 Mazda 3 vs. 2012 Honda Civic: Which One Should I Buy?

Compact cars are well-known for their cost-effectiveness, value and affordability as well as their small stature. In general, they make great commuter cars and are especially good for first-time cars for kids or college students heading out for the first...

Symptoms of a Bad or Failing Trunk Latch Release Cable

Common signs include the trunk not unlatching when the handle is pulled and the trunk latch handle feeling loose.

How to Replace a Distributor Rotor and Cap

Distributor caps and rotors keep the distributor clean and separate from the engine. Distributor caps may need to be replaced if the car won't start.

Thumping noise from front end

Hello. You likely are experiencing a problem with a hub bearing. I would also recommend having your brakes checked. If you need assistance with a repair, consider YourMechanic, as a certified mechanic will be able to come to your home...

A/C is not blowing cold air - 2007 Dodge Nitro

Unless the leak is large enough that refrigerant is just blowing out or somewhere obvious and all at once, the system has to be recharged with a dye installed with it. The dye will leak out with the refrigerant and...

I need to find the transmission range sensor

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com