Lincoln Zephyr Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(39)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(39)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a Lincoln Zephyr Intake Manifold Gaskets Replacement is $406 with $112 for parts and $294 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Lincoln ZephyrV6-3.0LService typeIntake Manifold Gaskets ReplacementEstimate$549.90Shop/Dealer Price$619.23 - $797.45
Show example Lincoln Zephyr Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Lincoln mechanics

Real customer reviews from Lincoln owners like you.

Excellent Rating

(39)

Rating Summary
34
3
0
1
1
34
3
0
1
1

Junard

12 years of experience
161 reviews
Junard
12 years of experience
Lincoln Zephyr V6-3.0L - Brake Pads Replacement (Front) - Philadelphia, Pennsylvania
Great

Ruben

36 years of experience
83 reviews
Ruben
36 years of experience
Lincoln Zephyr V6-3.0L - Car Starter Repair - Zephyrhills, Florida
Excellent, arrived right at scheduled time, and on a Sunday morning no less. Was very friendly and professional. Replaced a starter in about 45 min. (Would have been quicker if I stopped talking to him about the weather) My first time using Yourmechanic, will only use them for all work in the future. and will ask for Ruben every time. Like any first time user of an online company, I was somewhat skeptical until he showed up. All was great and the best part was he didn't try to sell me a lot of other stuff. Made a couple recommendation but didn't push it like others do.

Charles

25 years of experience
21 reviews
Charles
25 years of experience
Lincoln Zephyr V6-3.0L - Oil Pan Gasket - Cypress, Texas
Charles did a great job, professional and knowledgeable and he completed the job in less time than expected. Thank you sir!!

Mike

27 years of experience
265 reviews
Mike
27 years of experience
Lincoln Zephyr V6-3.0L - Interior Door Handle Replacement (Driver Side Front) - Dearborn, Michigan
Fast, efficient, knowledgeable about replacing the broken door handle.

Excellent Rating

(39)

Rating Summary
34
3
0
1
1
34
3
0
1
1
Number of Lincoln Zephyr services completed
429+
services done by our mechanics
TOTAL NUMBER OF EXPERT Lincoln MECHANICS
700+
experts on our platform

Recent articles & questions

P0297 OBD-II Trouble Code: Vehicle Overspeed Condition
P0297 P0297 code definition The P0297 code indicates that the car has been driven beyond the maximum speed to which it has been calibrated. What the P0297 code means The P0297 code means that the car has been operated at...
Symptoms of a Bad or Failing Speed Timing Sensor
Common signs include the transmission having difficulty shifting, Check Engine Light coming on, vehicle not starting, and loss of engine power.
I Have No Idea What's Wrong With My Car - Where Do I Begin?
Any driver can use their senses to diagnose a car problem. Use your sense of smell, touch, and hearing to figure out what's causing the issue.

How do I adjust the height of the seat belt?

Before driving, it’s important to adjust the height of the seat belt so that it is at a safe height. To raise the height of the shoulder strap, slide the belt adjuster upwards to the desired position. To lower the...

Heater not working

Hello. If the heater does not work I always check the coolant level first. If the coolant level for the engine is low then not much coolant will enter the heater core which results in little to no heat. If...

No Start. Fuel delivery issue

Hi there, thanks for writing in about your 1993 Toyota Pickup. You should check all the relay connections (https://www.yourmechanic.com/services/fuel-pump-relay-replacement) to see if the wire connections are corroded and losing relay connections to the relays. This vehicle is known to get...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com