Ford Windstar Car Thermostat Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(176)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(176)

Car Thermostat Replacement Service

How much does a Car Thermostat Replacement cost?

On average, the cost for a Ford Windstar Car Thermostat Replacement is $219 with $79 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2000 Ford WindstarV6-3.0LService typeCar Thermostat ReplacementEstimate$312.14Shop/Dealer Price$355.03 - $475.58
2001 Ford WindstarV6-3.8LService typeCar Thermostat ReplacementEstimate$316.27Shop/Dealer Price$360.67 - $489.76
1995 Ford WindstarV6-3.0LService typeCar Thermostat ReplacementEstimate$303.13Shop/Dealer Price$344.27 - $463.52
1995 Ford WindstarV6-3.8LService typeCar Thermostat ReplacementEstimate$310.37Shop/Dealer Price$353.32 - $478.00
1997 Ford WindstarV6-3.8LService typeCar Thermostat ReplacementEstimate$310.37Shop/Dealer Price$354.80 - $480.58
1998 Ford WindstarV6-3.0LService typeCar Thermostat ReplacementEstimate$313.59Shop/Dealer Price$357.49 - $484.69
1998 Ford WindstarV6-3.8LService typeCar Thermostat ReplacementEstimate$310.37Shop/Dealer Price$353.34 - $478.03
1996 Ford WindstarV6-3.8LService typeCar Thermostat ReplacementEstimate$310.37Shop/Dealer Price$353.32 - $478.00
Show example Ford Windstar Car Thermostat Replacement prices

What is an engine cooling system thermostat and how does it work?

The car's engine cooling system thermostat is a small valve within a cooling system passageway that opens and closes in response to the temperature of the circulating engine coolant. When your car is first started and the coolant is cold, the valve in the thermostat will be in the closed position, circulating the coolant flow only within the engine instead of flowing to the radiator, which allows the engine to warm up fast, promoting fuel efficiency, low emissions, and reduced engine deposits. Once the engine coolant reaches the design temperature, usually around 195 degrees, the valve will open and close as you drive in order to maintain a coolant temperature typically between 195 to 225 degrees Fahrenheit.

Thermostat

When to consider replacing the engine cooling system thermostat:

  • Engine overheats. A thermostat with the valve stuck closed is a common cause of engine overheating. However, since there are other causes of overheating, a mechanic will thoroughly inspect the cooling system prior to condemning the thermostat. Since it is usually not known how badly the engine overheated, the mechanic will also try to determine if there is evidence that the cylinder head gasket was blown. If so, it would be repaired prior to replacing the thermostat.
  • Temperature gauge reads too low or too high. Thermostats can get sticky, causing the engine temperature to stray from the optimal range. Your dash-mounted temperature gauge will notify you of this malfunction.
  • Cooling system repairs. All thermostats eventually fail. Therefore, if the cooling system is already open for major repairs, such as water pump or radiator replacement, it is recommended to install a new thermostat simply as insurance against future breakdown.

How do mechanics replace the engine cooling system thermostat?

  • Once the engine is completely cold, the radiator cap is loosened and enough coolant is drained from the radiator so the coolant level is below the thermostat housing.
  • The thermostat housing is removed and the thermostat and gasket are extracted. Note that some cars have more than one cooling system thermostat and both might need replacement.
  • All mounting surfaces on the thermostat housing are cleaned of old gasket material. A new gasket is applied and the thermostat is re-installed in the correct orientation and with the temperature sensing cylinder facing downward towards the engine.
  • The thermostat housing bolts are tightened to original equipment manufacturer (OEM) specifications using a calibrated inch-pound torque wrench.
  • The cooling system is refilled with the appropriate coolant type and the system is fully bled of all air.
  • The car engine is run until the normal operating temperature is reached, and while taking precautions with the hot coolant, the coolant level is rechecked while confirming there is flow through the radiator — either visually or with an infrared temperature gun. This will confirm the thermostat is open. Finally, the engine is checked for leaks.

Is it safe to drive with an engine cooling system thermostat problem?

No. If it has been determined that there is a thermostat problem, it should be repaired right away. Failure to do so can cause substantial and costly damage to the engine.

When replacing the engine cooling system thermostat keep in mind:

  • Engine overheating due to causes other than a faulty thermostat, will themselves damage a thermostat. Therefore, always replace the thermostat if the engine overheats, even if the thermostat was not the initial cause of the overheating.
  • The thermostat should be replaced anytime you have major work done on the coolant system. It is convenient and costs little during such repairs and insurance against future breakdown.
  • OEM thermostats are the best ones to use and you can request your mechanic to install only the OEM thermostat. Dealer supplied, OEM thermostats are sometimes more costly but are generally higher quality and specifically engineered for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(176)

Rating Summary
163
9
1
1
2
163
9
1
1
2

Jonathan

25 years of experience
42 reviews
Jonathan
25 years of experience
Windstar 2000 - Ignition Coil - Marietta, GA
Explains everything until you understand. Friendly Listens to the customer's concerns and if there is an issue is ready to fix any issues

William

30 years of experience
377 reviews
William
30 years of experience
Windstar 1996 - Car is slow to accelerate - Tolleson, AZ
Thank you

Arturo

25 years of experience
253 reviews
Arturo
25 years of experience
Windstar 2001 - Vacuum Booster - San Diego, CA
He showed up early, super nice and very quick!

Raymond

25 years of experience
137 reviews
Raymond
25 years of experience
Windstar 2001 - Brake Wheel Cylinder - Hesperia, CA
Great job! Thanks so much for getting me back on the road.

Excellent Rating

(176)

Rating Summary
163
9
1
1
2
163
9
1
1
2
Number of Ford Windstar services completed
1936+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1800+
experts on our platform

Recent articles & questions

Synthetic Oil: Should You Upgrade From Conventional to Synthetic?
The benefits of full synthetic oil for car engines.
P0523 OBD-II Trouble Code: Engine Oil Pressure Sensor/Switch High Voltage
P0523 trouble code means there is an issue with the engine oil pressure sensor often due to faulty wire connection or wrong engine oil.
How to Start a Car by Pushing
When all else fails, push starting a car with a manual transmission can be an option to get the engine to start.

How do you send numbers or names during a call with the HandsFreeLink?

If you need to send numbers or names, for instance if you’re trying to navigate a menu on the phone, you can do so with the HandsFreeLink® (HFL) system pretty easily. Here’s what you need to know. Press the talk...

Jerking reaction when accelerating

This may be a sign of a dirty or failing mass air flow sensor. The mass air flow sensor is a unit in the intake system that monitors air intake as it is mixed with fuel prior to being injected...

The Crankshaft Position Sensor broke at the block - how do i get it out? 1998 Chrysler Cirrus

Hello - I would soak it with penetrating oil (WD-40, PB Blaster, etc.) overnight, then try drilling the sensor for a screw/bolt extractor. If that fails, you may have to keep drilling with larger and larger bit sizes until, you...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com