Chevrolet K2500 Power Steering Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(33)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(33)

Power Steering Pump Replacement Service

How much does a Power Steering Pump Replacement cost?

On average, the cost for a Chevrolet K2500 Power Steering Pump Replacement is $247 with $107 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1994 Chevrolet K2500V8-6.5L DieselService typePower Steering Pump ReplacementEstimate$548.64Shop/Dealer Price$615.50 - $799.88
1996 Chevrolet K2500V8-5.0LService typePower Steering Pump ReplacementEstimate$1249.80Shop/Dealer Price$1492.92 - $2214.04
1995 Chevrolet K2500V8-7.4LService typePower Steering Pump ReplacementEstimate$530.62Shop/Dealer Price$594.00 - $775.77
1993 Chevrolet K2500V8-5.0LService typePower Steering Pump ReplacementEstimate$517.72Shop/Dealer Price$577.87 - $749.96
1999 Chevrolet K2500V8-7.4LService typePower Steering Pump ReplacementEstimate$530.62Shop/Dealer Price$596.94 - $780.92
1995 Chevrolet K2500V6-4.3LService typePower Steering Pump ReplacementEstimate$517.72Shop/Dealer Price$578.15 - $750.45
1994 Chevrolet K2500V8-6.5L Turbo DieselService typePower Steering Pump ReplacementEstimate$530.62Shop/Dealer Price$594.03 - $775.82
1995 Chevrolet K2500V8-6.5L DieselService typePower Steering Pump ReplacementEstimate$530.62Shop/Dealer Price$594.00 - $775.76
Show example Chevrolet K2500 Power Steering Pump Replacement prices

What is the power steering pump and how does it work?

The power steering pump is a belt-driven or electric-driven hydraulic pump that generates the hydraulic pressure needed to provide power steering assist. It develops output pressures of 1,000 PSI or more. The pump output is directed to the steering gear, often a rack and pinion type unit, where the hydraulic pressure pushes on the steering rack, greatly reducing the effort it would otherwise take to turn the steering wheel.

Power Steering

When to consider replacing the power steering pump:

  • Groaning or whining noise when turning. Noise can occur if there is wear on the pump bearings or impeller vanes. A low fluid level or trapped air can also cause noises. If the pump has already been operating while dry, adding fluid may not resolve the noise and replacement of the pump might be necessary.
  • Power steering fluid leaks. Leaks can develop at pump seals, threaded connections, hoses, or on the steering rack and pinion unit. Pump seal leaks will generally require a replacement.
  • Difficult steering. Should you notice it is harder to turn the steering wheel, it might mean the power steering pump output pressure is too low, or there could be blockages in the pump or lines.
  • Damage to the pump pulley. Should the pump pulley become damaged or is loose on the pump shaft, you might detect vibration, drive belt damage, or hard steering. Either the pulley will have to be serviced or the pump assembly replaced.

How do mechanics replace the power steering pump?

  • If driven by a drive belt, the power steering pump is bolted to the engine via a bracket that allows for adjustment of the pump drive belt. Once the engine is cold, and safe to work on, the drive belt is removed.
  • If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump.
  • The threaded connectors to the pump inlet and outlet are loosened and removed.
  • Any mounting bolts and brackets are removed so the pump can be removed.
  • If the old pump has failed catastrophically, or there is reason to suspect contaminants in the power steering hoses, the system is flushed.
  • The new pump is bolted on, the pressure and return hoses attached and the system is bled of all air. If pump is belt-driven, it is tightened to the manufacturer’s specification.
  • Finally, the engine is run and the car is road tested to confirm normal steering effort. If a new drive belt was installed, belt tension is measured again, and adjusted as needed, after the belt has run for a few minutes.

Is it safe to drive with a power steering pump problem?

No. If the power steering pump is operated without an adequate amount of fluid, and the pump reservoir will not hold fluid due to a large leak. The pump could seize, which would snap the serpentine belt and likely leave you stranded. If the pump turns and there is adequate fluid, but there is no power assist, it will require much greater effort to turn the steering wheel, and that presents inherent safety risks. Generally, the wisest course is to seek immediate repairs if you suspect a problem with any component in your car’s power steering system.

When replacing the power steering pump keep in mind:

  • Any belts driving the pump should be inspected and replaced as needed. The pump will only produce the required hydraulic pressure if it is driven by the belt at an adequate speed.
  • Power steering leaks from aged rubber hoses, particularly where the rubber is crimped to the steel tube, are not unusual and should be carefully inspected. The system operates under high pressure. The fluid is flammable, and if leaking fluid happens to contact a hot engine part, a fire might result. You always want to be sure the hoses and connections are sound.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(33)

Rating Summary
33
0
0
0
0
33
0
0
0
0

Pedro

32 years of experience
120 reviews
Pedro
32 years of experience
Chevrolet K2500 V8-5.7L - Tune-up - Hobart, Indiana
Really knows his stuff! Very polite & professional. Thank you very much

Joseph

21 years of experience
718 reviews
Joseph
21 years of experience
Chevrolet K2500 V8-5.7L - Car will not turn over - Clearfield, Utah
Excellent Joseph was very knowledgeable and personable.

Kanstantsin

20 years of experience
192 reviews
Kanstantsin
20 years of experience
Chevrolet K2500 V8-5.7L - Thermostat - Littleton, Colorado
Would hire again.

Michael

28 years of experience
672 reviews
Michael
28 years of experience
Chevrolet K2500 V8-5.7L - Window is not working - Mesa, Arizona
Mike is great!!!

Excellent Rating

(33)

Rating Summary
33
0
0
0
0
33
0
0
0
0
Number of Chevrolet K2500 services completed
363+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1700+
experts on our platform

Recent articles & questions

Signs Your Car Has a Blown Fuse
If you own your car long enough, you can assume that at some point, one or more of your...
How to Buy a Good Quality Shock Absorber
Shock Shock absorbers do exactly what the name says they do – they absorb the shock, or dampen the ride of your vehicle. Your car undergoes all manner of bouncing and shaking from the road, including potholes, speed bumps, quick...
How to Replace a Lost or Stolen Car Title in Louisiana
Likely Likely your car title isn't something you think about or are concerned about on a day to day basis that is until it becomes lost or stolen. Suddenly this small piece of paper becomes quite important. Your car title...

How Does Your ECU Use Sensor Data?

Today’s modern vehicles are made up of anywhere from one to seven computers that assist with the car’s day to day functions. An engine control unit (https://www.yourmechanic.com/article/how-your-ecu-uses-sensor-data) (ECU), is a computer that similar to that of a laptop or smartphone...

Tire has slow leak

Hello. If your tire has a slow leak, this is likely due to a small hole being in it. It is very common for people to drive over a nail, screw, or road debris. When the object is stuck in...

My truck won't shift to reverse

There are a few things that can cause this. Check the transmission fluid level to see if it is low. Sometimes low transmission fluid levels will prevent the transmission from shifting into gear. If you still have forward gears, but...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com