BMW 760i Tie Rod End Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Tie Rod End Replacement Service

How much does a Tie Rod End Replacement cost?

On average, the cost for a BMW 760i Tie Rod End Replacement is $185 with $90 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2004 BMW 760iV12-6.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$329.35Shop/Dealer Price$400.44 - $574.34
2006 BMW 760iV12-6.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$274.15Shop/Dealer Price$336.47 - $483.99
2004 BMW 760iV12-6.0LService typeTie Rod End - Rear Left Inner ReplacementEstimate$309.35Shop/Dealer Price$380.47 - $554.39
2004 BMW 760iV12-6.0LService typeTie Rod End - Rear Right Outer ReplacementEstimate$274.15Shop/Dealer Price$336.43 - $483.92
2005 BMW 760iV12-6.0LService typeTie Rod End - Front Left Outer ReplacementEstimate$274.15Shop/Dealer Price$336.50 - $484.04
2004 BMW 760iV12-6.0LService typeTie Rod End - Front Right Outer ReplacementEstimate$274.15Shop/Dealer Price$336.47 - $483.99
2005 BMW 760iV12-6.0LService typeTie Rod End - Front Left Inner ReplacementEstimate$314.35Shop/Dealer Price$385.23 - $558.97
2005 BMW 760iV12-6.0LService typeTie Rod End - Rear Right Inner ReplacementEstimate$314.35Shop/Dealer Price$385.89 - $560.11
Show example BMW 760i Tie Rod End Replacement prices

What are tie rod ends and how do they work?

Your car’s steering rack or gearbox (depending on the vehicle) is bolted in a fixed position to the frame of your vehicle. But the car’s wheels move up and down to smooth out road irregularities, and also left and right as you turn the steering wheel. The tie rod end is connected between the track rod of the steering assembly and the steering knuckle. A tie rod has a ball-and-socket joint to accommodate these movements. Cars will typically have two tie rod ends on each side: one inner tie rod end and one outer tie rod end — four total with a set of two per side. Tie rod ends are usually permanently greased but some may have Zerk fittings for re-greasing, including aftermarket ones. Tie rod ends are adjustable and accuracy is critical for proper front wheel alignment.

When to consider replacing tie rod ends:

  • Vehicle wandering, pulling, or premature tire wear out. Loose tie rod ends may cause the vehicle to not track straight ahead. You may also notice excessive tire wear on the front tires.
  • Missing, damaged, or leaking rubber boot or bellows. The grease in an outer tie rod end is retained by a rubber seal. If the seal has failed, the grease will leak out and the joint will be contaminated and worn down by road dirt. Inner tie rod ends are protected by extensible bellows. If the bellows has torn and is noticed early, only it needs to be replaced.
  • Obvious looseness in the component. Mechanics use specified tests to determine if there is wear in a tie rod end. For example, the resistance to turning of the ball stud in the outer tie rod end can be measured and compared against the original equipment manufacturer’s (OEM) specifications. However, without the use of any instruments, any detectable play in the ball stud indicates the tie rod end must be replaced. Excessive play will also make it impossible to properly set toe alignment.
  • Clunking noises, lack of smooth steering. Noise from the suspension on turning, or binding when you turn the steering wheel, could be due to tie rod end defects. Steering rack or power steering assist problems can account for these problems too.

How do mechanics replace tie rod ends?

  • The vehicle is jacked up and supported on steel safety stands.
  • The tire and wheel assembly is removed.
  • If possible, the existing tie rod end length is measured and recorded. Installing the new tie rod at the same length as the old helps in the alignment process.
  • The tie rod end adjusting lock nut or sleeve is loosened. Then, a tie end removal tool is used to separate the tie rod ball stud from the steering knuckle. The tie rod is then unthreaded from its connection to the inner tie rod end.
  • On a rack and pinion type steering system, if an inner tie rod end is being replaced, the tie rod steering shaft boot is removed and the tie rod unthreaded from the steering rack and the outer tie rod end.
  • New tie rod ends are installed with all fasteners and the adjusting lock nut tightened to the required OEM torque value. During installation, the length recorded during removal is applied to aid the later wheel alignment process.
  • With only a few exceptions, anytime a suspension component is removed and replaced on your car, the vehicle alignment must be inspected, measured, and adjusted to factory specifications. Using portable equipment, some mobile mechanics can perform a mobile alignment at your location. More likely though, the final step will be a trip to a local alignment shop for measurement, and adjustment as needed, of the vehicle alignment.

Is it safe to drive with a tie rod end problem?

No. Tie rods ends are a critical mechanical linkage in the steering system. If a known problem exists, such as wear, looseness, or binding, the possibility of sudden and unpredictable breakage of the tie rod remains, which would cause loss of steering control. Consequently, it is not safe to drive the car if the tie rod ends have a known deficiency. Tie rod ends should always be inspected per the maintenance schedule.

When replacing tie rods keep in mind:

  • It is recommended to replace tie rod ends in pairs. There are four tie rod ends on most vehicles. The outer tie rod ends — one per side — are most susceptible to wear and failure. If one outer tie rod end has failed, the other is probably not far behind.
  • After the repair is performed the vehicle must be aligned, either on a mobile basis or at a good alignment shop.
  • A good alignment job will provide you with pre and post-alignment printouts of your car’s alignment settings. A good shop will set the alignment to the “preferred” factory setting, not just the “allowed” settings. A job well-done will also have performed a careful inspection of the suspension beforehand to ensure the new alignment remains durable and stable. The best alignment results will be achieved if the tires on your car are not unevenly worn.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(12)

Rating Summary
11
0
0
0
1
11
0
0
0
1

Tung

16 years of experience
310 reviews
Tung
16 years of experience
BMW 760i V12-6.0L - Car is leaning to one side Inspection - Atlanta, Georgia
Tung was wonderful.

Nue

11 years of experience
6 reviews
Nue
11 years of experience
BMW 325Ci L6-2.5L - Tie Rod End Replacement (Front Left Outer, Front Right Outer) - Hillsboro, Oregon
Nick arrived on time with a great attitude and a smile. Nick completed the work agreed upon in record time and clean up after service was completed. I will definitely recommend Nick to anyone and definitely welcome Nick back on any future projects I need help.

Ben

41 years of experience
1421 reviews
Ben
41 years of experience
BMW X5 L6-3.0L - Tie Rod End Replacement (Front Left Outer) - Houston, Texas
Mr.Smith thank you for fixing my car. I am more knowledgeable about my car. My experience was so professional, enlightening and I trust your expertise. You're the BEST.

Matthew

10 years of experience
36 reviews
Matthew
10 years of experience
BMW 335i L6-3.0L Turbo - Tie Rod End Replacement (Front Left Inner, Front Left Outer) - Saint Louis, Missouri
Great job! Hard to find a real honest straight forward mechanic! I’ll be back!

Excellent Rating

(12)

Rating Summary
11
0
0
0
1
11
0
0
0
1
Number of BMW Tie Rod End Replacement services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

Top 10 Scenic Drives in Wyoming
Wyoming has a more diverse landscape than non-natives often think from prairielands to mountain ranges to lush forest regions. With a fairly low population density, most of the landscape is full of natural beauty and unscathed by man. There are...
How Can You Tell That Your Fuel Pump Isn’t Working?
The The fuel pump is responsible for getting fuel out of the gas tank and up to the engine. The pump itself is usually located inside the gas tank. There are a handful of symptoms to look out for that...
How Long Does a Wheel Stud Last?
The The tires on a car are among the most important parts. Tires are the only part of a car that actually touch the ground, which means that you will have to ensure that they are working properly at all...

Car runs rough and eventually stalls when idling or at traffic lights

Your stalling problem (https://www.yourmechanic.com/article/how-to-fix-a-stalling-car) may be due to a vacuum leak (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-a-vacuum-leak) in the engine, but one that only when it is warmed up. This would lead me to believe there is a possible problem with the EGR valve and...

Should i worry about the head gasket and stripped head bolt problems that seem to affect more the 2002-03 Camrys ? Is it all Camrys? 2005 Toyota Camry

Hello - unfortunately,, if you have a 2002-2006 Camry (gen 5 engines), the answer is "YES, worry". That engine has the cylinder head bolts going into an aluminum block without thread reinforcement, and the head bolts strip in the block....

Hot start issues

The air fuel ratio is off on your hot starts probably due to sensors or controls operating out of range or perhaps due to a stuck open EGR valve. Heat affects ignition coils and can also adversely affect sensors such...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com