BMW 135i Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

customer ratings

(3)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

customer ratings

(3)

Water Pump Replacement Estimate for BMW 135i

BMW 135i Water Pump Replacement costs $798 on average.

CarServiceEstimateShop/Dealer Price
2011 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1333.37Shop/Dealer Price$1672.73 - $2525.41
2013 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1303.37Shop/Dealer Price$1634.42 - $2480.87
2012 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1303.37Shop/Dealer Price$1634.41 - $2480.86
2008 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1303.37Shop/Dealer Price$1634.29 - $2480.65
2009 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1303.37Shop/Dealer Price$1634.50 - $2481.00
2010 BMW 135iL6-3.0L TurboService typeWater Pump ReplacementEstimate$1303.37Shop/Dealer Price$1634.41 - $2480.86
Show example BMW 135i Water Pump Replacement prices

Water Pump Replacement Service

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0
Number of BMW 135i Water Pump Replacement services completed
33+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

How to Make Your Car Driver's Seat More Comfortable
The most comfortable driver's seats are car seats that are properly adjusted, have warm car seat covers, and built-in lumbar support to prevent aches.
Understanding Chevrolet Oil-Life Monitor (OLM) System and Lights
Car symbols, or dashboard lights, are a car service reminder. The Chevrolet Oil Light Monitor system indicates when and what service your car needs.
P0623 OBD-II Trouble Code: Generator Lamp Control Circuit
P0623 means there is a voltage problem between the ECU and the generator control module due to bad battery or alternator, or a weak or dead battery.

Fromt left collision, curtain airbag didn't deploy. Should it have? I broke the window with my head.

Hi there. First and foremost, I'm glad you're able to send this question to YourMechanic.com - as an impact like you've described can be fatal in some cases. In regards to the side-air bag, the way in which they deploy...

Why would my 4x4 high and low light flash three times when start up and driving in my 2002 Ford Explorer

Hello. Most of the time when this is occurring it is due to an electrical issue with the 4X4 system. I usually remove all of the connections at the transfer case and clean them and add dielectric grease. That may...

Not getting fire, changed coil and camshaft sensor?

Your vehicle is equipped with a crankshaft position sensor. That sensor is on the primary side of the ignition circuit and consequently you should test the sensor and all wiring to the distributor to be sure it is functioning. If...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com