Popular articles

If the door open warning light is on but you believe all your doors and trunk are closed, there may be a mechanical issue with a door switch.

P0533 means the A/C refrigerant pressure is too high to safely function often due to inoperative cooling fans or too little or too much refrigerant.

If your car has a carburetor and it gets flooded, fuel is leaking, or the car smells of gas, you may need to replace the fuel return hose.

Poor air flow and an unusual odor can indicate it's time to replace the cabin air filter.

P0313 means a misfire has been detected in an engine cylinder with a low fuel reading, likely due to an insufficient fuel level or bad ignition coil.

There There are few things more frightening than hearing buzzing or clicking from your car when you’re trying to start it. It could mean any number of things, but chances are that it means you have a faulty car battery....

P9063 means there is an issue with the pressure control solenoid A control circuit due to low or dirty transmission fluid, faulty wiring or solenoid.

The P003A trouble code means the Electronic Computer Module (ECM) has detected an issue in the turbocharger or supercharger system.

P0057 P0057 trouble code definition P0057 is a code that sets when the powertrain control module senses that the voltage is low on the bank 2 sensor 2 oxygen sensor. What the P0057 code means When a P0057 trouble code...

The The purpose of the power steering system is to ensure easy handling and precise direction as a vehicle is being driven. The power steering system assists steering by guiding part of an engine’s power towards one front wheel or...

P2443 P2443 code definition Secondary Air Injection System Switching Valve Stuck Closed Bank 2 What the P2443 code means P2443 is an OBD-II generic code for the engine control module (ECM) detecting the exhaust pressure sensor is detecting no exhaust...

Trouble code P0393 means the PCM has detected a high voltage reading from the camshaft position sensor for camshaft sensor B in engine bank 2.

Tar is a black, sticky substance that comes from asphalting on the road. A solvent-based spray or a few household items can be used to remove it.

P2444 P2444 code definition The P2444 diagnostic trouble code is an indication that the bank 1 secondary air injection system pump is stuck. Related Trouble Codes: P2445 OBD-II Trouble Code: Secondary Air Injection System Pump Stuck Off Bank 1...

P2251 P2251 code definition O2 Sensor Negative Current Control Circuit/Open Bank 1 Sensor 1 What the P2251 code means P2251 is an OBD-II generic code. The engine control module (ECM) monitors the negative current control of the O2 sensor heater...

Those Those who drive on the roadways in Vermont generally know they are required to follow numerous traffic laws when traveling throughout the state. However, motorists must also be aware of and comply with the laws regarding the equipment on...

Part Part of what makes a modern battery work so effectively is the ‘wet cell’ design they utilize. In a wet cell battery, there is a mixture of sulfuric acid and distilled water (called electrolyte) that connects all of the...

P2209 P2209 trouble code definition The P2209 OBD-II trouble code registers when the Powertrain Control Module (PCM) detects an abnormal reading in the NOx (nitric oxide and nitrogen dioxide) sensor for the Bank 1 side of the engine. What the...

P0772 means that a problem in the shift solenoid was detected, usually in the form of an incorrect gear ratio due to low or dirty transmission fluid.

P0960 P0960 code definition The P0960 code is a generic powertrain code related to the transmission, including pressure faults and sensor failures. In this case, the engine control module (ECM) has received a signal noting that the pressure control solenoid...

If you see an emergency vehicle while driving, know how to safely pull over to give it the right of way.

It's hard to know what to do when your car breaks down. If your car breaks down out of town, safely pull off the road and call for help.

P2247 P2247 code definition The P2247 diagnostic trouble code is an indication that there is a problem with the bank 2 sensor 1 oxygen (O2) sensor reference voltage circuit. Related Trouble Codes: P2243 OBD-II Trouble Code: O2 Sensor Ref...

A clutch switch failure means that your vehicle will not be able to start. The contacts within the switch or the wiring may be corroded.

The electronic ignition pickup is part of the ignition distributor. Signs of failure include intermittent misfiring or failure all at once.