Saturn Outlook Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(3)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(3)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Saturn Outlook Water Pump Replacement is $495 with $187 for parts and $308 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2009 Saturn OutlookV6-3.6LService typeWater Pump ReplacementEstimate$714.00Shop/Dealer Price$815.17 - $1100.86
2007 Saturn OutlookV6-3.6LService typeWater Pump ReplacementEstimate$694.18Shop/Dealer Price$791.46 - $1074.24
2010 Saturn OutlookV6-3.6LService typeWater Pump ReplacementEstimate$723.38Shop/Dealer Price$821.09 - $1104.18
2008 Saturn OutlookV6-3.6LService typeWater Pump ReplacementEstimate$694.18Shop/Dealer Price$791.51 - $1074.33
Show example Saturn Outlook Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Saturn mechanics

Real customer reviews from Saturn owners like you.

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0

Excellent Rating

(3)

Rating Summary
3
0
0
0
0
3
0
0
0
0
Number of Saturn Outlook Water Pump Replacement services completed
33+
services done by our mechanics
TOTAL NUMBER OF EXPERT Saturn MECHANICS
700+
experts on our platform

Recent articles & questions

Least Expensive Luxury Cars to Insure
You’ve You’ve done well for yourself and are now in the market for a vehicle upgrade. It’s time to ditch the rattletrap you’ve been driving and snag yourself a car with some premium options. How do you decide which car...
Disabled Driver Laws and Permits in Maine
It It is important to be familiar with your state’s disabled driver laws. Each state has its own particular guidelines, and Maine is no exception. How do you know if you are eligible for a disabled driver permit and/or license...
P0058 OBD-II trouble code: HO2S Heater Control Circuit High (Bank 2 Sensor 2)
P0058 P0058 trouble code definition The definition of the trouble code P0058 is heated oxygen sensor heater control circuit high voltage bank 2 sensor 2. What the P0058 code means When this code is stored in the powertrain control module...

Opinion about Cadillac Northstar motors

The old Northstar motors were horrible. They blew head gaskets. Eventually, they made them better, but they are very complex V8 engines with all kinds of computer controls on them and they cost a fortune to fix. So if you...

My front end is making a popping noise

This is a common sign of a failing CV joint. A CV (Constant Velocity) joint is a shaft that connects the transmission to the wheels, essentially transferring the power from the drive train directly to the wheels. The CV joint...

What could be causing my VSA to engage when I'm not going that fast around and sweeping turn?

The VSA system may be turned off or there is a defective or dirty wheel speed sensor. Check all of the wheel speed sensors and ensure that they are all clean and free from oil or metal as they are...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com