Nissan Cube Brake Pad Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Brake Pad Replacement Service

How much does a Brake Pad Replacement cost?

On average, the cost for a Nissan Cube Brake Pad Replacement is $221 with $81 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2013 Nissan CubeL4-1.8LService typeBrake Pads - Rear ReplacementEstimate$407.48Shop/Dealer Price$474.20 - $666.26
2011 Nissan CubeL4-1.8LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.22 - $471.44
2014 Nissan CubeL4-1.8LService typeBrake Pads - Rear ReplacementEstimate$398.47Shop/Dealer Price$463.45 - $654.20
2010 Nissan CubeL4-1.8LService typeBrake Pads - Rear ReplacementEstimate$398.47Shop/Dealer Price$463.45 - $654.20
2013 Nissan CubeL4-1.8LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$350.72 - $474.06
2009 Nissan CubeL4-1.8LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.39 - $471.73
2012 Nissan CubeL4-1.8LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.26 - $471.51
2014 Nissan CubeL4-1.8LService typeBrake Pads - Front ReplacementEstimate$307.11Shop/Dealer Price$349.25 - $471.48
Show example Nissan Cube Brake Pad Replacement prices

What are brake pads and how do they work?

Brake pads consist of friction material that is bonded to a sturdy steel backing plate. When you push on the brake pedal, the friction material on the brake pads is forced against the inner and outer surfaces of the steel brake rotor under tremendous pressure. The resulting friction causes the wheels on your car to slow rapidly allowing for a quick, safe and controlled stop. After thousands of miles, this friction material eventually wears away, and the brake rotor wears away as well, requiring replacement.

Brakes-Service

When to replace brake pads?

Here are several indications that you need new brake pads:

  • Wear indicator on vehicle dashboard. When the friction material on the brake pads is worn to within 2 mm of the pad backing plate, replacement of the pads is necessary. Most newer cars today have electronics built into the brake pad. When the pad is at a point that it needs to be replaced, a symbol will appear on your vehicle dashboard’s instrument cluster. Consult your owner’s manual to learn what the symbol looks like.
  • High pitched squeal when braking. When the friction material on the pads is worn close to the backing plate, you may hear a squealing or squeaking noise as you drive regardless of whether you are applying the brakes or not. That squealing or squeaking noise is designed to make you aware that the brake pads are getting low and need to be inspected. If all of the friction material on the brake pad has been worn away, you will hear grinding and scraping noises when you apply the brakes. Pad replacement is mandatory at this point and the vehicle is unsafe to drive until corrected.
  • Brake pedal pulsation or vehicle vibration. Over time, brake rotors may develop excessive thickness variation (>.001 inches), excessive runout on the wheel hub (> .002 inches), or the brake rotor may warp due to high operating temperatures. If these defects exist, you may notice pulsation in the brake pedal or steering wheel during braking. New pads and rotor resurfacing or replacement will be required if the rotor has any of the above-mentioned deficiencies.
  • Vehicle pulling or wandering on braking. If your car pulls to the right or left during braking, that could be a sign of a sticking brake caliper, misalignment of the suspension, and sometimes tire defects or uneven tire inflation from side-to-side. The mechanic who inspects your vehicle will determine if new brake pads alone will resolve the issue or if other repairs are needed.
  • High mileage on existing pads. Regardless of whether any of the above brake system symptoms occur, every 10,000 miles a mechanic should measure the thickness of the remaining friction material on the brake pads and perform a thorough visual inspection of the braking system.
  • Brake system warning lights and/or maintenance reminder messages. Should your brake system warning light ever illuminates, or a brake system related maintenance reminder message appears in the driver information display, have your vehicle inspected and repaired as soon as possible.

How do mechanics replace brake pads?

Normally, pad replacement requires these steps:

  • Confirm the thickness of the remaining friction material on the brake pads. If the remaining friction material is less than 2 mm in thickness, pad replacement is warranted.
  • Visually inspect the brake rotor surface that contacts the pad (for scoring, pitting, grooves, rust) and measure the brake rotor with precision tools for thickness variation, run-out and warpage.
  • Inspect the caliper, torque plate, pads, and rotors to determine if the caliper is operating freely (i.e., inspect for stuck calipers).
  • Install new pads and any additional recommended components (e.g., rotors, if rotors depart from OEM specifications) only with customer approval of course.
  • Lubricate brake system components, such as caliper sliding pins, and inspect the condition of the brake fluid. Top off brake fluid as required.
  • Perform a basic 50 point safety inspection of your vehicle.
  • Finally, the mechanic will test drive your vehicle to confirm normal operation of the brake system.

Is it safe to drive with a brake pad problem?

Driving a vehicle with a known deficiency in the braking system is unsafe and consequently is not recommended. Worn out brake pads can increase stopping distances and so for your safety, it is always advised that worn out brake pads be replaced promptly. Further driving is not recommended and you should request service at your earliest convenience if any of the following circumstances exist: stopping distances are much greater than what you are accustomed to; the brake pedal is not firm or is low; there is loss of braking power assist; the vehicle pulls severely to one side on braking; or the brake system warning light is on.

If you detect unusual noises, such as squealing or grinding, but stopping distances are close to what you are used to, and the brake pedal is firm, and there are no warning lights, it may be safe to proceed to your destination but schedule service at your earliest convenience. When it comes to the brakes on your vehicle, always err on the side of caution and have a mechanic check your brake pads and braking system at the first indication of a problem.

When replacing brake pads keep in mind:

Brake pads must always be replaced as a set, that is both wheels (driver and passenger side) on an axle, front or rear, must be serviced. If brake pads on only one side of the car were replaced, your car might pull to one side when you apply the brakes. Often, resurfacing or replacement of the brake rotors is necessary and a competent mechanic will always measure for wear and damage to the brake rotors and advise you as to whether rotor replacement or re-surfacing is needed.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Nissan mechanics

Real customer reviews from Nissan owners like you.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0

Ramiro

0 years of experience
76 reviews
Ramiro
0 years of experience
Cube 2011 - Brake Pads - Seattle, WA
Ramiro got right down to business and did all of the services methodically and without any hassle. He was both professional and personable. I would recommend him and request him again.

Shawn

22 years of experience
62 reviews
Shawn
22 years of experience
Cube 2011 - Car is making a noise - Yorktown, VA
Excellent and very professional

Bryan

4 years of experience
58 reviews
Bryan
4 years of experience
Cube 2009 - Catalytic Converter - Los Angeles, CA
Great customer service. I would highly recommend his services, explained in good detail the service I was having done

Manuel

25 years of experience
511 reviews
Manuel
25 years of experience
Cube 2009 - Brake Rotor/Disc - Santa Ana, CA
Awesome! Finished quickly, and did an excellent job. Will definitely go to him again

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0
Number of Nissan Cube Brake Pad Replacement services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Nissan MECHANICS
1600+
experts on our platform

Recent articles & questions

Insurance Requirements For Car Registration in All States
Car insurance is mandatory when registering a vehicle. Find out what the insurance requirements are in your state or when traveling to another state.
What Is E85 Ethanol?
E85 E85 ethanol is a fuel that can be used to power internal-combustion engines. Some vehicles can use E85 and gasoline, while others are tuned for E85 only. E85 is named as such because it is 85% alcohol. The other...
How to Replace a Tailgate Lock Solenoid
The tailgate lock solenoid controls the locking mechanism on your trunk or tailgate and needs to be replaced if your tailgate doesn't unlock.

Car leaks coolant

If you have a coolant leak, I would address it as soon as possible. A leak in the cooling system can cause the vehicle to overheat, which can cause serious engine damage. I would recommend having the vehicle's cooling system...

Heat inside car stays warm for minute then blows cold until I turn heat off for a minute and try again.

Hi there. The engine always at operating temperature leads me to believe, the thermostat is not the cause, for no heat inside the vehicle. There are several possibilities for no heat inside, the heater control valve is malfunctioning (https://www.yourmechanic.com/services/heater-control-valve-replacement), the...

Engine starts and dies immediately

The first thing to check for is air leaks. Any air that gets into the engine without going through the air mass meter to be measured will cause the fuel/air mix to be leaner. For that or some other reason,...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com