Mercedes-Benz SL320 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz SL320 Brake Drum Replacement is $323 with $190 for parts and $133 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1994 Mercedes-Benz SL320L6-3.2LService typeBrake Drum ReplacementEstimate$618.08Shop/Dealer Price$753.49 - $1092.75
1997 Mercedes-Benz SL320L6-3.2LService typeBrake Drum ReplacementEstimate$512.21Shop/Dealer Price$631.56 - $934.38
1995 Mercedes-Benz SL320L6-3.2LService typeBrake Drum ReplacementEstimate$525.49Shop/Dealer Price$648.15 - $960.94
1996 Mercedes-Benz SL320L6-3.2LService typeBrake Drum ReplacementEstimate$525.49Shop/Dealer Price$648.10 - $960.84
Show example Mercedes-Benz SL320 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Jarius

21 years of experience
49 reviews
Jarius
21 years of experience
Mercedes-Benz SL320 L6-3.2L - Car Battery Replacement - Silver Spring, Maryland
Jarius Foster was early for the appointment, very courteous, efficient and skilled. While I was expecting an hour long visit, Mr. Foster was finish in just 30 minutes. I would recommend him to all.

Chris

15 years of experience
312 reviews
Chris
15 years of experience
Mercedes-Benz SL320 L6-3.2L - Back To School Promo - San Diego, California
Chris does excellent work, he gets right down to business and finishes ASAP so you can get on with your day!

Maurice

21 years of experience
39 reviews
Maurice
21 years of experience
Mercedes-Benz SL320 L6-3.2L - Fuel is leaking from gas tank - Charleston, South Carolina
On time. Gracious. Patient. Analytical. Knowledgeable.

Robert

12 years of experience
125 reviews
Robert
12 years of experience
Mercedes-Benz SL320 L6-3.2L - Car is not starting - Silver Spring, Maryland
Robert was early to our appointment, diligent, thorough, personable, efficient and friendly.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Mercedes-Benz SL320 services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercedes-Benz MECHANICS
1100+
experts on our platform

Recent articles & questions

A Buyer's Guide to the 2012 Mazda CX-7
If If you want an SUV, but don’t care as much about the “utility” part as you do the “sport” features, you should take a look at what the 2012 Mazda CX-7 has to offer. Key Features With a turbo...
2012 Jeep Patriot vs. 2012 Honda CR-V: Which One Should I Buy?
The mid-size SUV is a great vehicle for getting a lot of people from one place to another, with a decent price point and pretty good ongoing fuel economy. While they are never going to get the amazing gas mileage...
Insurance Requirements for Car Registration in Utah
All All drivers who are residents of Utah, or who have been in the state of Utah for at least 90 days are required to carry liability insurance or “financial responsibility,” through a Utah insurance provider, in order to cover...

What should I know about the air conditioner filter?

Filters are used in several locations on your car. The most familiar is probably the engine air filter, but you also have a filter for your air conditioning system. This filter does pretty much the same thing as the one...

gas pedal problem

It sounds like you have a problem with your pedal position sensor or throttle position sensors. Using a scan tool, test the pedal position sensor by reading the output of the sensor as you slowly press down on the pedal....

Puff blue smoke on startup

Your engine does not have a PCV valve. The engine is equipped with crankcase vent tubes that do not need replaced or cleaned unless line is broken. You may have valve seals that are leaking oil into the exhaust valve...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com