Mercedes-Benz 560SEL Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercedes-Benz 560SEL Brake Drum Replacement is $370 with $209 for parts and $161 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1989 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$624.74	Shop/Dealer Price$761.81 - $1106.07
1987 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$590.74	Shop/Dealer Price$727.87 - $1072.17
1986 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$590.74	Shop/Dealer Price$727.86 - $1072.16
1988 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$590.74	Shop/Dealer Price$727.79 - $1072.04
1990 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$579.26	Shop/Dealer Price$713.56 - $1049.28
1991 Mercedes-Benz 560SELV8-5.6L	Service typeBrake Drum Replacement	Estimate$579.26	Shop/Dealer Price$713.51 - $1049.20

Show example Mercedes-Benz 560SEL Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Mercedes-Benz mechanics

Real customer reviews from Mercedes-Benz owners like you.

Excellent Rating

(5)

Rating Summary

3

1

1

0

0

3

1

1

0

0

SEE REVIEWS NEAR ME

Scott

28 years of experience

7 reviews

Scott

28 years of experience

by Jimmy

Mercedes-Benz 560SEL V8-5.6L - Car is not starting - Oklahoma City, Oklahoma

He was on time, very knowledgable

Jason

24 years of experience

57 reviews

Jason

24 years of experience

by Dawn

Mercedes-Benz 560SEL V8-5.6L - Spark Plug Replacement - Norman, Oklahoma

He was a blessing. Thank you for fixing my ride. He was nice and very helpful.i will call agin

Ruben

17 years of experience

169 reviews

Ruben

17 years of experience

by Sylvester

Mercedes-Benz 560SEL V8-5.6L - Alternator - Charlotte, North Carolina

After the two disappointing missed appointments and lack of communication everything else was 100%

Nicholas

21 years of experience

354 reviews

Request Nicholas

Nicholas

21 years of experience

Request Nicholas

by Jonas

Mercedes-Benz 560SEL V8-5.6L - Battery is dead Inspection - Denver, Colorado

Nicholas arrives at the set time. He seemed to know his mechanics although he also diagnosed a leaky gasket cover. He strongly recommended IED getting

Excellent Rating

(5)

Rating Summary

3

1

1

0

0

3

1

1

0

0

SEE REVIEWS NEAR ME

Recent articles & questions

How to Replace a Lost or Stolen Car Title in Indiana

Without Without a car title, you’re in a tight spot if you decide to sell the car or trade it in on a new one. The same thing applies if you move out of Indiana – you can’t register it...

P0080 OBD-II Trouble Code: Exhaust Valve Control Solenoid Circuit High (Bank 1)

P0080 P0080 trouble code definition P0080 is in reference to the bank 1 exhaust valve control solenoid. The vehicle may have a bank 1 and bank 2 control solenoid. This code may be seen in association with P0078 and P0079....

The Traveler’s Guide to Driving in Peru

Peru Peru has some fascinating places to visit (https://www.tripadvisor.com/Attractions-g294311-Activities-Peru.html), and having a rental vehicle will make it much easier to reach them. Some of the places you may want to see include Machu Pichu, the Sacred Valley, Museum Larco, the...

My 1991 Mercury Cougar LS has a replaced alternator and new battery but it seems the battery dies over night and the car will not start.

Hi there. It seems that there is a Parasitic Load on your battery. This is a load of something on when the key is out of the ignition switch and the doors shut. To check this condition perform the following:...

Hello, do you know how much it costs to fixed a damaged axel on a 2005 Hyundai Elantra?

At auto parts stores, the axle costs roughly $70 on up. It takes about 1 to 2 hours to install the axle. The job requires special tools though and to ensure a trouble free result, the axle output seal (https://www.yourmechanic.com/services/axle-shaft-seal-replacement)...

I have a 2008 Nissan Rogue SL AWD with 135000 miles on it. I am having a vibration issue in the steering wheel and gas pedal that

The wheels should be inspected for dents and measured for run-out. Some tire constructions will cause vibration no matter how well "balanced" the tires appear to be on a dynamic balancer. The only way to be reasonably sure that a...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com