Mazda 323 Front Crankshaft Seal Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6)

Front Crankshaft Seal Replacement Service

How much does a Front Crankshaft Seal Replacement cost?

On average, the cost for a Mazda 323 Front Crankshaft Seal Replacement is $191 with $23 for parts and $168 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1993 Mazda 323L4-1.6LService typeFront Crankshaft Seal ReplacementEstimate$346.14Shop/Dealer Price$390.50 - $513.84
1991 Mazda 323L4-1.8LService typeFront Crankshaft Seal ReplacementEstimate$220.81Shop/Dealer Price$234.41 - $270.28
1992 Mazda 323L4-1.6LService typeFront Crankshaft Seal ReplacementEstimate$335.33Shop/Dealer Price$377.59 - $499.37
1991 Mazda 323L4-1.6LService typeFront Crankshaft Seal ReplacementEstimate$335.33Shop/Dealer Price$377.59 - $499.37
1995 Mazda 323L4-1.6LService typeFront Crankshaft Seal ReplacementEstimate$220.67Shop/Dealer Price$236.04 - $273.14
1994 Mazda 323L4-1.6LService typeFront Crankshaft Seal ReplacementEstimate$335.33Shop/Dealer Price$377.76 - $499.66
1995 Mazda 323L4-1.8LService typeFront Crankshaft Seal ReplacementEstimate$220.81Shop/Dealer Price$234.46 - $270.36
1994 Mazda 323L4-1.8LService typeFront Crankshaft Seal ReplacementEstimate$220.81Shop/Dealer Price$234.44 - $270.33
Show example Mazda 323 Front Crankshaft Seal Replacement prices

What is the Front Crankshaft Seal all about?

A number of mechanisms must work together to make your vehicle move forward. One of the most important is the crankshaft, which converts rotary into linear motion; i.e., it transforms the force created by the engine's pistons moving up and down into a force that moves in a circular motion that causes a car’s wheel to turn. Enclosed in what’s called a crankcase—the largest cavity in the engine block, just below the cylinders—the crankshaft must be completely lubricated, essentially submerged in oil, to spin nearly friction-free and do its job properly.

Consequently, there are seals located at either end of the crankshaft that allow it to spin freely and keep engine oil from escaping the engine block, as well as prevent contaminants and other debris from entering and causing damage to the mechanism. Since there are two ends of the crankshaft, there are two types of seals: the front crankshaft seal and the rear crankshaft seal, also known as the front main and rear main seals.

Keep in mind:

  • Loss of oil will eventually cause serious internal engine damage.
  • Inspect the sealing surface of the crankshaft or the crankshaft pulley (depending on the engine design) for damage when replacing the crankshaft seal.
  • Oil degrades rubber components.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The crankshaft damper and timing belt is removed
  • The crankshaft seal is removed and a new one installed
  • The timing belt and cover along with crankshaft damper is reinstalled
  • The engine accessory belts are installed and the vehicle is lowered off of the jack stands

Our recommendation:

One of the most important parts of your car, crankshaft seals are typically made from a durable material, such as a synthetic rubber or silicone, designed to handle the extreme pressure and temperatures as well as the caustic chemicals in your engine oil. Because they are exposed to such abuse, main seals are subject to a lot of wear and tear. And whether you are talking a front or rear main seal, replacement is the only cure when one malfunctions.

The good news is that the seals are relatively inexpensive components. The bad news is that neither is easy to replace.

Front seal: The front seal is located behind the main pulley that drives all the belts, which is, of course, always spinning. The main pulley throws any leaking oil out in a big circle. It can get thrown up on the alternator, steering pump, belts, in short anything attached to the front of the engine and cause a real mess and eventually some serious damage. Consequently, it has to be removed along with many of the components attached to the front of the block to replace the front main seal.

Rear seal: The rear crankshaft seal is placed along with the transmission; therefore, the process of replacing it requires the removal of transmission, as well as the clutch and flywheel assembly. This is a very involved job.

What common symptoms indicate you may need to replace the Front Crankshaft Seal?

  • Oil leaking from the front crank pulley.
  • Oil dripping from the bottom of the clutch housing, where the block and transmission meet.
  • Clutch slip caused by oil spraying on the clutch.

How important is this service?

Letting either crankshaft seal continue to leak can be detrimental to your vehicle’s continued operation. Besides the maladies caused by driving around with little to no oil flowing in the engine, the faulty seal will be spread oil through the engine bay and undercarriage of your car as you drive, a mess that is difficult to clean up and can be a fire hazard. Replacing is better addressed sooner than later.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mazda mechanics

Real customer reviews from Mazda owners like you.

Excellent Rating

(6)

Rating Summary
5
1
0
0
0
5
1
0
0
0

Bryce

17 years of experience
26 reviews
Bryce
17 years of experience
Mazda 323 L4-1.6L - Car will not move when in gear. Won't go forward or in reverse. Please advise. - Fort Worth, Texas

Jose

17 years of experience
324 reviews
Jose
17 years of experience
Mazda 323 L4-1.6L - Radiator - Hollywood, Florida
he did excellent work

Chris

19 years of experience
174 reviews
Chris
19 years of experience
Mazda 323 L4-1.6L - Brake Master Cylinder - Hollywood, Florida
Excellent job.

Steve

38 years of experience
149 reviews
Steve
38 years of experience
Mazda 323 L4-1.6L - Oil Change - Hayward, California
My car is old and easy to work on. Steve got the oil changed in minutes. Very convenient for any mechanic. I liked this service for the price to my personal wallet.

Excellent Rating

(6)

Rating Summary
5
1
0
0
0
5
1
0
0
0
Number of Mazda 323 services completed
66+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mazda MECHANICS
1100+
experts on our platform

Recent articles & questions

The Best Used Cars to Buy for Senior Citizens
Everyone Everyone needs a way to get around. You need to get groceries, get to doctors’ appointments, visit with family and more. However, senior citizens have very different needs when it comes to buying a used car than other demographics....
A Buyer’s Guide to the 2012 Jeep Grand Cherokee
Though Though the Jeep Grand Cherokee is not a new model, it got a complete redesign in 2011, and the 2012 Jeep Grand Cherokee saw even more improvements. While other SUV manufacturers have sat on their laurels, Jeep has done...
Industry News for Automotive Techs: October 29 - November 4
Toyota and Getaround's smartphone key, future McLaren cars, DMCA car hacking, a fire at Ford's headquarters, and Chevrolet's SEMA 2016 show cars.

Nissan Pulsar 2015 heating problem

Hi and thanks for your question. It sounds like you have two different things that could be fixed. There is either a vacuum line that split open on the blend doors to the heater and a/c system, or the blend...

Smoke that is not coming from exhaust when going above 60 mph.

Hey there. If the smoke is not coming from the exhaust, it may be possible that the white smoke is coming from oil leaking onto a hot exhaust manifold or another piece of the motor or exhaust. The PCV valve...

System too lean bank 1

Hi There, Typically, a lean fuel condition will produce DTC code P0171, which indicates a lean fuel condition often times associated with "bank 1 or 2 too lean" as you have indicated. A number of things may cause code P0171...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com