Chrysler 300M Wheel Bearings Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(115)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(115)

Wheel Bearings Replacement Service

How much does a Wheel Bearings Replacement cost?

On average, the cost for a Chrysler 300M Wheel Bearings Replacement is $236 with $96 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2002 Chrysler 300MV6-3.5LService typeWheel Bearings - Driver Side Rear ReplacementEstimate$346.96Shop/Dealer Price$398.55 - $545.22
2002 Chrysler 300MV6-3.5LService typeWheel Bearings - Driver Side Front ReplacementEstimate$419.93Shop/Dealer Price$490.25 - $697.08
2002 Chrysler 300MV6-3.5LService typeWheel Bearings - Passenger Side Rear ReplacementEstimate$337.95Shop/Dealer Price$387.80 - $533.16
1999 Chrysler 300MV6-3.5LService typeWheel Bearings - Passenger Side Front ReplacementEstimate$419.93Shop/Dealer Price$490.27 - $697.12
2004 Chrysler 300MV6-3.5LService typeWheel Bearings - Passenger Side Rear ReplacementEstimate$337.95Shop/Dealer Price$389.27 - $535.74
2003 Chrysler 300MV6-3.5LService typeWheel Bearings - Driver Side Front ReplacementEstimate$419.93Shop/Dealer Price$490.41 - $697.37
2003 Chrysler 300MV6-3.5LService typeWheel Bearings - Passenger Side Rear ReplacementEstimate$337.95Shop/Dealer Price$387.81 - $533.19
2004 Chrysler 300MV6-3.5LService typeWheel Bearings - Driver Side Front ReplacementEstimate$419.93Shop/Dealer Price$490.27 - $697.12
Show example Chrysler 300M Wheel Bearings Replacement prices

What are wheel bearings and how do they work?

A wheel bearing assembly consists of rolling elements, such as hardened steel ball bearings or roller bearings, that roll on and around hardened steel bearing races. The wheel bearings support the front and rear axle, and all the weight of your car. Wheel bearings are made with a high-precision technique using extremely hard steel in order to withstand all the normal impacts that occur to the wheel and tire assembly as you drive along the road.

When to replace wheel bearings?

  • Growling or grinding noise from a wheel. Failed or failing wheel bearings make a very characteristic growling noise which will grow louder as the bearing wear progresses. If you believe the wheel bearing noise is coming from one side of the car, you can self-diagnosis your wheel bearing as you drive the car by loading and unloading vehicle weight You can do this by “swerving” from side-to-side. For example, if the noise markedly increases when you swerve to left, which shifts the vehicle’s weight to the right, then it often indicates the wheel bearing on the right is failing.

  • Axial or radial play in the wheel or wheel hub. Should the wheel hub move up and down or in and out, the bearing may be worn.

  • Vibration in the steering wheel or vehicle body and/or wandering. Vibration and lack of directional stability could be consequences of loose or worn out wheel bearings.

  • Tire and wheel assembly does not turn smoothly. With the wheel jacked up, and the car not in gear, the wheel should rotate smoothly. Rough or inconsistent movement, which is often accompanied by noise, can signify damaged bearings. Be sure the brakes are not dragging as you perform this check.

How do mechanics replace wheel bearings?

The complexity of wheel bearing replacement varies greatly depending on the vehicle make, model, year, the wheel position (front versus rear), and the drive type (AWD versus FWD):

  • On vehicles with unitized wheel bearing/hub assemblies, the brake rotor and caliper are removed.
  • The large axle nut is removed, the axle is pushed back through the center of the unitized hub assembly, and three (or more) bolts holding the hub assembly to the steering knuckle are removed.
  • The hub assembly is then removed from the knuckle. On installation of the new hub assembly to the knuckle, the bolts are torqued to the factory specification. In many cases, it is required to discard the old axle nut and replace with a new one. Special attention must be given to tightening the axle nut to the exact factory specification because over or under-tightening can damage the newly installed bearing. All YourMechanic professionals use calibrated torque wrenches on these critical fasteners.
  • Finally, the brake rotor and brake caliper are re-attached, the wheel installed and the car is road tested.
  • On vehicles where the wheel bearing is pressed into a cavity within the steering knuckle, the steering knuckle must be removed from the vehicle in order to press out the old bearing and press in the new bearing.
  • On some vehicles, the wheel bearing is pressed onto an axle shaft and thus the axle must be extracted from the axle carrier. This will apply to certain trucks.

Is it safe to drive with a wheel bearing problem?

No. Wheel bearing failure is usually gradual, although in some cases it starts immediately after the dramatic impact of the wheel and tire assembly with a deep pothole. Wheel bearings can sometimes make noise for quite some time before you experience a catastrophic failure that would result in complete separation of the wheel and tire assembly from the axle. Generally, the risk of sudden failure increases with the noise level. But strictly speaking, once the bearing has started to fail it is impossible to predict exactly when it will fail completely. So it should not continue to be driven. Were a failing bearing to seize or break while you are moving, you could experience loss of control of the vehicle. Once you receive a conclusive diagnostic that a wheel bearing has failed, replace the bearing promptly.

When replacing wheel bearings, keep in mind:

  • If the car has a substantial number of miles on the failed bearing (100,000 miles or more), it is a good idea to replace both bearings (driver and passenger) on the axle at the same time.
  • Wheel bearing noise can be confused with tire noise from defective tires. In difficult cases, a mechanic will apply remote wireless microphones at all 4 wheel positions, and then drive the car while listening to a remote receiver, switching between wheel positions to pinpoint the location of the failed bearing.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chrysler mechanics

Real customer reviews from Chrysler owners like you.

Excellent Rating

(115)

Rating Summary
101
5
1
2
6
101
5
1
2
6

William

14 years of experience
95 reviews
William
14 years of experience
300M 2003 - Power Steering Fluid Service - Denver, CO
Wonderful again.

William

14 years of experience
95 reviews
William
14 years of experience
300M 2003 - Brake System Flush - Denver, CO
Wonderful again.

William

14 years of experience
95 reviews
William
14 years of experience
300M 2003 - Battery - Denver, CO
William was timely, respectful and thorough in dealing with me and my vehicle.

Collins

8 years of experience
362 reviews
Collins
8 years of experience
300M 1999 - Headlight Bulb - Atlanta, GA
On time, professional and completed job without issues.

Excellent Rating

(115)

Rating Summary
101
5
1
2
6
101
5
1
2
6
Number of Chrysler 300M services completed
1265+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chrysler MECHANICS
1200+
experts on our platform

Recent articles & questions

How to Remove Frost from Car Windows
Dealing with ice on your windshield can be hard to remove. Luckily there are multiple ways to defrost the ice on your windshield to make things easy.
P0228 OBD-II Trouble Code: Throttle/Pedal Position Sensor/Switch C Circuit High Input
P0228 P0228 code definition Throttle/Pedal Position Sensor/Switch C Circuit High Input What the P0228 code means P0228 is a generic OBD-II code which indicates that the throttle/pedal position sensor/switch C circuit has a high input problem causing the sensor input...
How Long Does a Hood Lift Support Shock Last?
There There are a number of instances where you will have to get under the hood of your car. Whether it is to do a visual inspection or to find out what is causing issues, being able to lift the...

Fuel injectors misfiring

Hello. If you are getting codes for the injectors themselves then they may be electrically failing and in need of replacement. I would typically check their resistance with an ohm meter to verify if they are bad, as a bad...

the flywheel bolts broke how hard and what will cost to get fixed ballpark figure

When a bolt breaks off inside the bolt hole, getting it out usually requires drilling. If the transmission is inside the vehicle still and there is not enough room for a drill, the transmission will require removal in order to...

Car is stalling at stops unless I continue to give it gas.

Hi Aaron. Thanks for contacting us tonight. While there are a few components on your list that contribute to idling effectively, there are several that are more critical that are likely dirty or damaged. Some of the possible parts that...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com