Chevrolet C1500 Brake Drum Replacement Costs

Estimate price near me

Service Location

Customer Ratings

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

See availability

Customer Ratings

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Chevrolet C1500 Brake Drum Replacement is $633 with $177 for parts and $456 for labor. Prices may vary depending on your location.

Car	Service	Estimate	Shop/Dealer Price
1995 Chevrolet C1500V8-5.0L	Service typeBrake Drum Replacement	Estimate$912.71	Shop/Dealer Price$1050.91 - $1357.49
1989 Chevrolet C1500V8-5.0L	Service typeBrake Drum Replacement	Estimate$809.21	Shop/Dealer Price$945.62 - $1246.63
1995 Chevrolet C1500V8-6.5L Turbo Diesel	Service typeBrake Drum Replacement	Estimate$816.71	Shop/Dealer Price$954.99 - $1261.62
1997 Chevrolet C1500V8-5.7L	Service typeBrake Drum Replacement	Estimate$816.71	Shop/Dealer Price$954.88 - $1261.43
1993 Chevrolet C1500V8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$816.71	Shop/Dealer Price$955.06 - $1261.75
1998 Chevrolet C1500V6-4.3L	Service typeBrake Drum Replacement	Estimate$816.71	Shop/Dealer Price$954.99 - $1261.62
1988 Chevrolet C1500V8-6.2L Diesel	Service typeBrake Drum Replacement	Estimate$833.21	Shop/Dealer Price$968.96 - $1269.48
1995 Chevrolet C1500V8-5.7L	Service typeBrake Drum Replacement	Estimate$840.71	Shop/Dealer Price$980.12 - $1287.61

Show example Chevrolet C1500 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

Raise the vehicle and safely support it using steel jack stands.
Remove tire and wheel assembly.
Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee

Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(217)

Rating Summary

198

10

3

1

5

198

10

3

1

5

SEE REVIEWS NEAR ME

Jacob

12 years of experience

329 reviews

Jacob

12 years of experience

by Pamela

Chevrolet C1500 V6-4.3L - Brake Wheel Cylinder Replacement (Passenger Side) - Richardson, Texas

Jacob was prompt and efficient! He really did a great job and found some other issues with the vehicle which will be having repaired. A lifesaver great personality! Will definitely book with him again.

Tyler

27 years of experience

178 reviews

Tyler

27 years of experience

by Daniel

Chevrolet C1500 V8-5.7L - Expansion Valve (Orifice Tube) - Houston, Texas

Tyler was very professional. Explained everything that was wrong with my air conditioner on my truck. I would highly recommend Tyler to my friends. He is an asset to your company. I am a happy camper. Thanks Tyler for taking care of my problem.

Lee

38 years of experience

220 reviews

Lee

38 years of experience

by Regino

Chevrolet C1500 V8-5.7L - Distributor - Norman, Oklahoma

great

Johnathon

9 years of experience

161 reviews

Request Johnathon

Johnathon

9 years of experience

Request Johnathon

by Sandra

Chevrolet C1500 V8-5.7L - Car is not starting - Fresno, California

Knew what was wrong with my vehicle before he came by.

Excellent Rating

(217)

Rating Summary

198

10

3

1

5

198

10

3

1

5

SEE REVIEWS NEAR ME

Recent articles & questions

How Does Traction Control Work?

Traction control is a car safety feature that prevents wheels from spinning on low-grip surfaces. Electric sensors in your car make the system work.

How to Replace a Lost or Stolen Car Title in New York

Do Do you have plans of selling your car in the future? What about transferring ownership, perhaps passing it over to one of your kids when they turn 16? In order to do either of these you’ll need to have...

P0357 OBD-II Trouble Code: Ignition Coil G Primary/Secondary Circuit Malfunction

P0357 P0357 code definition When the P0357 code is stored, it means that the PCM has detected one or more ignition coils (https://www.yourmechanic.com/services/ignition-coil-replacement) is faulty to some degree. What the P0357 code means Most vehicles with an OBD-II system utilize...

What does the all-wheel drive (AWD) Warning Light mean in a 2012 Honda CR-V?

The all-wheel drive (AWD) Warning Light is located on the instrument panel. When the light comes on, the AWD system is either not working, or is overheating and has been made inactive. Tip Like all warning lights, the AWD warning...

Won't shift when warm

Hello there, many different faults may be causing your 1988 Chevrolet C2500 not to shift. The most common would be low transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service), shift linkage, transmission range sensor (https://www.yourmechanic.com/services/transmission-speed-sensor-replacement), shift solenoid (https://www.yourmechanic.com/services/downshift-solenoid-replacement), or a mechanical transmission fault. Have a...

I have a 2008 Nissan Rogue SL AWD with 135000 miles on it. I am having a vibration issue in the steering wheel and gas pedal that

The wheels should be inspected for dents and measured for run-out. Some tire constructions will cause vibration no matter how well "balanced" the tires appear to be on a dynamic balancer. The only way to be reasonably sure that a...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com