BMW 525iT Intake Manifold Gaskets Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(21)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(21)

Intake Manifold Gaskets Replacement Service

How much does a Intake Manifold Gaskets Replacement cost?

On average, the cost for a BMW 525iT Intake Manifold Gaskets Replacement is $778 with $120 for parts and $658 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1993 BMW 525iTL6-2.5LService typeIntake Manifold Gaskets ReplacementEstimate$968.02Shop/Dealer Price$1057.51 - $1259.36
Show example BMW 525iT Intake Manifold Gaskets Replacement prices

What is an intake manifold gasket and how does it work?

The intake on an engine may be made up of a lower intake manifold and an upper intake manifold or plenum. The lower intake manifold is a cast aluminum or molded plastic chamber bolted to the cylinder head of the engine. The intake manifold must be tightly sealed to the cylinder head(s) using a gasket in order to prevent air, oil, or engine coolant leaks.

When to consider replacing the intake manifold gasket:

Internal or external leaks. Due to constant temperature expansion and contraction of engine parts or overheating, the gasket’s ability to seal properly can be ruined, resulting in problems such as:

  • Internal or external engine coolant leaks. In some applications, the manifold has cooling passages within. If the manifold seal to the engine fails, coolant can leak externally or even into the engine oil crankcase, where coolant can be noticed in the engine oil.
  • Engine overheating. If the leak at the manifold is a leak of engine coolant, it can lead to engine overheating. However, there are other causes of engine overheating, so a mechanic would have to determine the actual cause.
  • External oil leaks. On some 6 and 8 cylinder engines, the intake manifold sits atop an oil-lubricated area of the engine block. If the manifold gasket has failed, oil can leak from the block to the exterior of the engine.
  • Poor engine operation, lean operation, rough idle. Vacuum air leaks into the manifold due to a defective gasket that will upset the air-fuel ratio. The engine may run poorly.
  • Check engine light. Minor leaks at the intake manifold gasket will not usually cause the check engine light to illuminate. However, as a leak persists, it may grow larger and it possible for the leak to degrade engine performance enough that it will cause a trouble code to set, which will cause the check engine light to illuminate.

How do mechanics replace the intake manifold gasket?

  • Working on a cold engine, the engine cover is removed. If the intake manifold has internal cooling system passageways, the engine coolant is drained below the level of those passageways.
  • The accelerator cable assembly and cruise control cable are removed and set aside. All electrical connections and emission and vacuum lines in the way of the intake are removed. Ignition components, such as the coil, are removed as needed. If the car has an upper plenum, that is removed and set aside.
  • If the fuel rail is bolted to the intake manifold, the supply and return connections to the fuel rail are disconnected.
  • Once all connections to the manifold are clear, the manifold is unbolted and removed from the engine.
  • Aluminum and plastic manifolds are checked with a machinist’s straightedge to ensure the surface flatness does not exceed the original equipment manufacturer’s specification. If the surface of a manifold is not flat, the new gasket will not seal properly. Plastic manifolds are checked for cracks, heat damage, and warpage.
  • Once the manifold is deemed re-usable or replaced as needed, the new gasket is applied, the manifold is put in position and the mounting bolts are torqued with a calibrated torque wrench in the OEM specified sequence. In some applications, RTV sealant must be applied in corners of the mounting surface or specified hard-to-seal spots, per the service manual.
  • All removed components are then re-installed in the reverse of the above steps.
  • Finally, the vehicle is run and checked for leaks, and test driven.

Is it safe to drive with an intake manifold gasket problem?

Yes. The principal concern with a leaking intake manifold gasket is potential damage to the engine, depending on where the leak is. Although the vehicle will generally be safe to drive, you should schedule service as soon as possible to minimize the chances of additional costly damage. If the leak involves coolant, it could lead to engine overheating damage or the coolant could contaminate the engine oil, which can damage the engine bearings. If there is an air leak to the cylinders, it can cause lean operation which could overheat the catalytic converter.

When replacing the intake manifold gasket keep in mind:

  • In engines where coolant flows through the intake manifold, a leaking intake manifold gasket can be either the cause of or result of engine overheating. If you have a leaking intake manifold gasket, and the engine has overheated, the entire engine should be inspected for damage, such as a blown head gasket. The engine cooling system thermostat should be replaced because engine overheating can damage the cooling system thermostat.
  • Some car engine designs are more likely than others to experience leaking intake manifold gaskets due to material and design issues. Your mechanic can inform you if your car represents one of these cases. Many times a re-designed gasket, or altered installation technique and torque values, will be relevant to avoid a recurrence of any leaks. Mechanics will consult Technical Service Bulletins to determine if any unique circumstance exists for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(21)

Rating Summary
20
0
0
0
1
20
0
0
0
1

Victor

12 years of experience
211 reviews
Victor
12 years of experience
BMW 325i L6-2.5L - Intake Manifold Gaskets Replacement - Chesapeake, Virginia
Definitely knew his way around a Bimmer. Took about the time he thought. Very knowledgeable and was able to let me know about things I might need to take care of with my car coming up.

John

37 years of experience
565 reviews
John
37 years of experience
BMW X1 L4-2.0L Turbo - Intake Manifold Gaskets - Folsom, California
John was very knowledgeable about his work. He was on time and completed the repair quickly and diligently. I appreciate his work and highly recommend him.

Tien

24 years of experience
903 reviews
Tien
24 years of experience
BMW 750Li V8-4.8L - Intake Manifold Gaskets - San Ramon, California
very prompt, professional and get the job done correctly

Carlos

17 years of experience
362 reviews
Carlos
17 years of experience
BMW 325i L6-3.0L - Intake Manifold Gaskets - Irving, Texas
This guy awasom he did great job with my BMW 325I model 2006

Excellent Rating

(21)

Rating Summary
20
0
0
0
1
20
0
0
0
1
Number of BMW Intake Manifold Gaskets Replacement services completed
231+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1200+
experts on our platform

Recent articles & questions

Disabled Driver Laws and Permits in Florida
Florida Florida has its own specific requirements for disabled driving permits. The following are some of the rules and guidelines that you must follow in the state of Florida to qualify as a disabled driver. How do I know if...
The Guide to Legal Car Modifications in Minnesota
ARENA Creative / Shutterstock.com Whether currently living in the state or planning to move to Minnesota in the near future, you need to make sure that you understand the restrictions on vehicle modifications. The following will help...
Windshield Laws in Florida
If If you drive, you already know there are many laws that you have to follow while on the roadways. However, states also have requirements concerning the windshield that motorists are required to follow as well. The following are the...

Serpentine belt came off

This vehicle is equipped with an automatic belt tensioner. So, if the belt slid off while driving, either the tensioner is weak or the pulleys are out of alignment. Also, there could be oil leaking down onto the belt, or...

Symptoms of an AC condenser going bad.

The condenser (https://www.yourmechanic.com/services/ac-condenser-replacement) if it was not cooling properly, will cause the switch to shut off the A/C, and then once it cools enough, will allow the A/C to come back on. It would be hard to know if connection...

my truck stalled yesterday and i received an engine code of p2110 now it wont start turns over but not getting gas

This P2110 code (https://www.yourmechanic.com/article/p2110-obd-ii-trouble-code-throttle-actuator-control-system-forced-limited-rpm-by-jay) relates to the electronic throttle control which can be potentially caused by the following: Faulty Electronic Throttle Control (ETC) Electronic Throttle Control (ETC) harness is open or shorted Electronic Throttle Control (ETC) circuit having poor electrical...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com