BMW 228i Car Thermostat Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(8)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(8)

Car Thermostat Replacement Service

How much does a Car Thermostat Replacement cost?

On average, the cost for a BMW 228i Car Thermostat Replacement is $331 with $217 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2015 BMW 228iL4-2.0L TurboService typeCar Thermostat ReplacementEstimate$571.01Shop/Dealer Price$700.27 - $1040.78
2014 BMW 228iL4-2.0L TurboService typeCar Thermostat ReplacementEstimate$547.01Shop/Dealer Price$676.30 - $1016.85
2016 BMW 228iL4-2.0L TurboService typeCar Thermostat ReplacementEstimate$547.01Shop/Dealer Price$676.30 - $1016.84
Show example BMW 228i Car Thermostat Replacement prices

What is an engine cooling system thermostat and how does it work?

The car's engine cooling system thermostat is a small valve within a cooling system passageway that opens and closes in response to the temperature of the circulating engine coolant. When your car is first started and the coolant is cold, the valve in the thermostat will be in the closed position, circulating the coolant flow only within the engine instead of flowing to the radiator, which allows the engine to warm up fast, promoting fuel efficiency, low emissions, and reduced engine deposits. Once the engine coolant reaches the design temperature, usually around 195 degrees, the valve will open and close as you drive in order to maintain a coolant temperature typically between 195 to 225 degrees Fahrenheit.

Thermostat

When to consider replacing the engine cooling system thermostat:

  • Engine overheats. A thermostat with the valve stuck closed is a common cause of engine overheating. However, since there are other causes of overheating, a mechanic will thoroughly inspect the cooling system prior to condemning the thermostat. Since it is usually not known how badly the engine overheated, the mechanic will also try to determine if there is evidence that the cylinder head gasket was blown. If so, it would be repaired prior to replacing the thermostat.
  • Temperature gauge reads too low or too high. Thermostats can get sticky, causing the engine temperature to stray from the optimal range. Your dash-mounted temperature gauge will notify you of this malfunction.
  • Cooling system repairs. All thermostats eventually fail. Therefore, if the cooling system is already open for major repairs, such as water pump or radiator replacement, it is recommended to install a new thermostat simply as insurance against future breakdown.

How do mechanics replace the engine cooling system thermostat?

  • Once the engine is completely cold, the radiator cap is loosened and enough coolant is drained from the radiator so the coolant level is below the thermostat housing.
  • The thermostat housing is removed and the thermostat and gasket are extracted. Note that some cars have more than one cooling system thermostat and both might need replacement.
  • All mounting surfaces on the thermostat housing are cleaned of old gasket material. A new gasket is applied and the thermostat is re-installed in the correct orientation and with the temperature sensing cylinder facing downward towards the engine.
  • The thermostat housing bolts are tightened to original equipment manufacturer (OEM) specifications using a calibrated inch-pound torque wrench.
  • The cooling system is refilled with the appropriate coolant type and the system is fully bled of all air.
  • The car engine is run until the normal operating temperature is reached, and while taking precautions with the hot coolant, the coolant level is rechecked while confirming there is flow through the radiator — either visually or with an infrared temperature gun. This will confirm the thermostat is open. Finally, the engine is checked for leaks.

Is it safe to drive with an engine cooling system thermostat problem?

No. If it has been determined that there is a thermostat problem, it should be repaired right away. Failure to do so can cause substantial and costly damage to the engine.

When replacing the engine cooling system thermostat keep in mind:

  • Engine overheating due to causes other than a faulty thermostat, will themselves damage a thermostat. Therefore, always replace the thermostat if the engine overheats, even if the thermostat was not the initial cause of the overheating.
  • The thermostat should be replaced anytime you have major work done on the coolant system. It is convenient and costs little during such repairs and insurance against future breakdown.
  • OEM thermostats are the best ones to use and you can request your mechanic to install only the OEM thermostat. Dealer supplied, OEM thermostats are sometimes more costly but are generally higher quality and specifically engineered for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(8)

Rating Summary
8
0
0
0
0
8
0
0
0
0

Excellent Rating

(8)

Rating Summary
8
0
0
0
0
8
0
0
0
0
Number of BMW 228i services completed
88+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Horn Switch
If the horn makes no sound or sounds different, or if you do not find any blown fuses, you may need to replace the horn switch.
P0240 OBD-II Trouble Code: Turbocharger Boost Sensor B Circuit Range/Performance
P0240 P0240 code definition Turbocharger Boost Sensor B Circuit Range/Performance What the P0240 code means P0240 is an OBD-II generic code triggered when the Engine Control Module (ECM) detects the intake boost pressure sensor B input circuit range or performance...
How to Understand Compression and Power Systems in Small Engines
Being familiar with basic compression and power system functions of a four-stroke engine can help you diagnose and fix issues with your car.

Warning lights and loss of power

When the EML light comes on there could be a range of issues from big to small. The main issue with this is that when the vehicle sets this light, it will also put the car into a limp home...

I Had my oil changed on 5/28/16. On 5/31/16 the check engine light came on. On 6/5/16 the low oil pressure turn off engine came on

Hello, From what you describe it would not appear to me that something went wrong during your oil change. If the level is correct on the dipstick and the engine runs and sounds okay, then it is probably something else....

Service advance trac light on and all lights on dash flash on and off as well as rpm need temp needle and speed bounce up and down

Hi Josue. Thanks for sending in your question tonight. What you are describing sounds a lot like a communication fault with the ECU or an electrical short in the steering column/behind the dashboard. Trying to diagnose this problem and recommend...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com