Nissan 280ZX Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Nissan 280ZX Power Steering Pressure Hose Replacement is $211 with $107 for parts and $104 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1981 Nissan 280ZXL6-2.8L TurboService typePower Steering Pressure Hose ReplacementEstimate$339.85Shop/Dealer Price$404.19 - $572.46
1982 Nissan 280ZXL6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$317.85Shop/Dealer Price$382.21 - $550.50
1981 Nissan 280ZXL6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$317.85Shop/Dealer Price$382.21 - $550.49
1983 Nissan 280ZXL6-2.8L TurboService typePower Steering Pressure Hose ReplacementEstimate$317.85Shop/Dealer Price$382.18 - $550.45
1980 Nissan 280ZXL6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$317.85Shop/Dealer Price$382.23 - $550.52
1983 Nissan 280ZXL6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$317.85Shop/Dealer Price$382.21 - $550.49
1982 Nissan 280ZXL6-2.8L TurboService typePower Steering Pressure Hose ReplacementEstimate$323.35Shop/Dealer Price$387.56 - $555.73
1979 Nissan 280ZXL6-2.8LService typePower Steering Pressure Hose ReplacementEstimate$757.87Shop/Dealer Price$931.12 - $1425.49
Show example Nissan 280ZX Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Nissan mechanics

Real customer reviews from Nissan owners like you.

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0

Joseph

20 years of experience
640 reviews
Joseph
20 years of experience
Nissan 280ZX L6-2.8L - Car is not starting - Salt Lake City, Utah
Showed up on time, was down to earth and friendly. He diagnosed the issue fairly quickly, and let me know what to do to fix it. I'd definitely recommend him to my friends when they find themselves needing a mechanic.

Trung

12 years of experience
412 reviews
Trung
12 years of experience
Nissan 280ZX L6-2.8L - Smell in the car - Santa Clara, California
Trung did an excellent job. Found out the gas smell was a fuel canister hose that needed to be replaced.

Joseph

33 years of experience
540 reviews
Joseph
33 years of experience
Nissan 280ZX L6-2.8L - Clutch Master Cylinder - Dallas, Texas
Joseph was prompt, knowledgable, tested thoroughly and was a pleasure to work with.

Jimmi

27 years of experience
231 reviews
Jimmi
27 years of experience
Nissan 280ZX L6-2.8L - Clutch Master Cylinder & Slave Cylinder Replacement - Winter Springs, Florida
Prompt and professional.

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0
Number of Nissan 280ZX services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Nissan MECHANICS
1500+
experts on our platform

Recent articles & questions

Symptoms of a Bad or Failing Throttle Return Spring
Common signs include engine RPM staying high even after the accelerator is depressed and the gas pedal feeling spongy or not returning to position.
The Guide to Right-of-Way Laws in Wisconsin
Vehicles Vehicles and pedestrians are inevitably going to meet in traffic, and sometimes there will be no signal lights or signs to regulate the movement of traffic. That is why there are right-of-way laws in place – to identify who...
How to Replace a License Plate Light
When a license plate light bulb goes out, it may be illegal in some states to drive in public. Here's a guide on how to replace it.

Do I have a damaged head gasket?

Hi there. This can be a bad head gasket or it may be something much smaller. If the coolant temperature gauge is staying in the normal range then it may just have a leak in the system. If there is...

Why will the car go into drive but won’t move??

Hi Ashley. Thanks for contacting us tonight. Sometimes this problem is caused by a damaged shift solenoid, contaminated transmission fluid or a torque converter that is wearing our or already damaged. It's also possible for internal transmission components to be...

While driving my 2005 Chevy Duramax a check [engine](/topics-engine-chevy/) light came on and a code read of p2563. I have looked into what it means and was wondering is it dangerous or bad to continue to drive it

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com