Ford Custom 300 Lubricate Driveshaft at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(19,242)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(19,242)

Lubricate Driveshaft Service

How much does a Lubricate Driveshaft cost?

On average, the cost for a Ford Custom 300 Lubricate Driveshaft is $95 with $0 for parts and $95 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1960 Ford Custom 300L6-3.6LService typeLubricate DriveshaftEstimate$114.99Shop/Dealer Price$124.99 - $132.49
1960 Ford Custom 300V8-5.8LService typeLubricate DriveshaftEstimate$94.99Shop/Dealer Price$105.01 - $112.52
1960 Ford Custom 300V8-4.8LService typeLubricate DriveshaftEstimate$94.99Shop/Dealer Price$105.01 - $112.52
Show example Ford Custom 300 Lubricate Driveshaft prices

What is lubricating the driveshaft all about?

Along the drivetrain, whenever torque needs to travel from one place to another, a driveshaft is used. Some cars have two driveshafts under them, usually for four-wheel-drive applications. U-Joints are couplings that hold sections of driveshaft together and can withstand large amounts of torque. The U-joint and the slip both need lubrication to work smoothly. This means lubricant needs to be applied to every point where the driveshaft meets another section of shaft or any other part of the vehicle.

Keep in mind:

  • While lubricating will help with scraping noise and minor vibration, it will not repair actually broken parts.
  • Inspect the parts of the the driveshaft to make sure they do not need full replacement.
  • Even small spots of excess wear are bad on parts that withstand so much torque, no problem is too small to be addressed on the driveshaft.

How it's done:

  • The vehicle is raised and supported on jack stands
  • The slip joints and U-joints on all drive shafts are located
  • The Zerk grease fittings on the slip joint and U-joints are located
  • New grease is pumped into the grease fittings with a grease gun
  • The vehicle is lowered off of the jack stands

Our recommendation:

Check the manual of your vehicle to see if the manufacturer has specific instructions on servicing and lubricating the driveshaft. If the manufacturer suggests it is time for a service or if the vehicle has symptoms of a malfunctioning driveshaft, then it should be done immediately. These parts are under a lot of force and will usually fail when the car is in motion. While under the vehicle, inspect all of the connections along the drivetrain and keep an eye out for any parts that seems excessively worn. Bring a rag and wipe any mud or dust off to check for damage.

What are the common symptoms indicating you need to lubricate the driveshaft?

  • Clicking or grating sounds while the vehicle is in gear
  • Vibration in the vehicle while it is running

How important is this service?

This service is very important. Poor lubrication is one of the top reasons why driveshafts fail. When they do fail, driveshafts will fail while in motion and can take out more expensive parts around them. These preventative maintenance steps are extremely important in order to avoid more costs down the road.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(19,242)

Rating Summary
18,054
638
125
102
323
18,054
638
125
102
323

Carlton

39 years of experience
14 reviews
Carlton
39 years of experience
Ford F-150 V8-5.0L - Lubricate Driveshaft - Woodbridge, Virginia
He was not able to perform the service because my drive shaft is sealed. He took a look at it and said it was good, however after I started driving again, the clunk and noise is still there. I am not satisfied with the service provided by your website. I paid $80 for a person to come over and do and inspection on my car. Had I taken the truck to his shop he would have not charged me after looking at it for 2 minutes like he did at my home. I think it’s fair to pay the gentleman for his time and drive ($40), however I don’t think it’s for for me to pay you the remainder. If you are going to offer these types of services, the. Your website should be savvy enough to be able to tell me that this job was not one he could have done at my home and saved me the money. I feel like I should get a partial refund since the job was not done. I should note that Carlton “Wayne” was great.

Theodore

16 years of experience
1604 reviews
Theodore
16 years of experience
Ford Crown Victoria V8-4.6L - Car is not starting - Bellevue, Washington
On time, very efficient

Galen

27 years of experience
35 reviews
Galen
27 years of experience
Ford Explorer V6-4.0L - Oil Change - Citrus Heights, California
Was hesitant to try Your Mechanic again after the last few appointments we had and the other mechanics always showing up super late (or not at all). Galen was right on time and finished up right before I had to leave for work. He was very pleasant and knowledgeable and will definitely book him specifically again when needed.

Juan

10 years of experience
216 reviews
Juan
10 years of experience
Ford Explorer V6-4.0L - Car is not starting - Long Beach, California
I use your mechanic all the time and they never let me down. Juan was on time, answered all my questions, and got my car running in an hour. He gave me a custom quote on some other things I wanted worked on. Will definitely use him again for other work.

Excellent Rating

(19,242)

Rating Summary
18,054
638
125
102
323
18,054
638
125
102
323
Number of Ford services completed
211662+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

How to Renew Your Car Registration in Georgia
As As a driver on the Georgia roadways, you will need to make sure that you have all of the appropriate paperwork in order to stay in compliance with the laws. There are a variety of things that you will...
P2638 OBD-II Trouble Code: Torque Management Feedback Signal 'A' Range/Performance
P2638 P2638 code definition If the Powertrain Control Module (PCM) stores a P2638 trouble code, it indicates that a signal malfunction has been detected in the PCM or one of the other support modules, dealing specifically with the torque management...
P0298 OBD-II Trouble Code: Engine Oil Over Temperature Condition
P0298 means that the engine is or has recently overheated due to low coolant level, faulty cooling fan, thermostat, or radiator.

AC blowing warm air.

The AC compressor clutch coil assembly may be inoperative causing your problem. The complete system would need checked. I would recommend having a mechanic, like the certified ones at YourMechanic, come and check it out for you to see what...

Valve cover oil leaks

Thank you for your inquiry. The valve cover seal is a common failure item and generally and easy fix. In your case, the upper intake plenum/manifold wraps over the top of the engine and must be removed to complete the...

My [engine](/topics-engine-chevy/) bogs down at full throttle

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com