Dodge Ram 1500 Van Water Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Water Pump Replacement Service

How much does a Water Pump Replacement cost?

On average, the cost for a Dodge Ram 1500 Van Water Pump Replacement is $425 with $173 for parts and $252 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2002 Dodge Ram 1500 VanV8-5.2LService typeWater Pump ReplacementEstimate$1136.08Shop/Dealer Price$1240.84 - $1513.79
2003 Dodge Ram 1500 VanV8-5.2LService typeWater Pump ReplacementEstimate$608.36Shop/Dealer Price$698.06 - $959.72
2000 Dodge Ram 1500 VanV6-3.9LService typeWater Pump ReplacementEstimate$725.15Shop/Dealer Price$816.38 - $1079.19
2003 Dodge Ram 1500 VanV6-3.9LService typeWater Pump ReplacementEstimate$608.36Shop/Dealer Price$698.10 - $959.79
1999 Dodge Ram 1500 VanV6-3.9LService typeWater Pump ReplacementEstimate$725.15Shop/Dealer Price$820.21 - $1085.89
2001 Dodge Ram 1500 VanV8-5.9LService typeWater Pump ReplacementEstimate$608.36Shop/Dealer Price$698.35 - $960.24
2002 Dodge Ram 1500 VanV8-5.9LService typeWater Pump ReplacementEstimate$608.36Shop/Dealer Price$698.13 - $959.84
2000 Dodge Ram 1500 VanV8-5.2LService typeWater Pump ReplacementEstimate$608.36Shop/Dealer Price$698.10 - $959.79
Show example Dodge Ram 1500 Van Water Pump Replacement prices

What is a water pump and how does it work?

The water pump is a belt or chain-driven engine accessory bolted to the engine above the crankshaft pulley. The pump housing has an impeller that circulates engine coolant through the cooling system passageways in the engine block and cylinder head, on to the radiator, where the coolant temperature is reduced. . The lower temperature coolant then flows back to the water inlet on the engine and the water pump continues the cycle.

When to consider replacing the water pump:

  • Coolant leaks or overheating. The water pump impeller shaft is supported by a bearing. Eventually, the bearing or seal can wear and leak or damage the impeller. Many water pumps have weep holes near the pump bearing. If you see significant leakage from that weep hole, it is time to replace the pump.
  • Bearing roughness or noise. If the water pump shaft does not turn smoothly or the pump is noisy, the bearing is excessively worn. Pump replacement will be necessary.
  • Timing belt replacement. In engines where the water pump is driven by the timing belt, it is a good idea to replace the water pump at the same time the timing belt is replaced. The extensive work explains why it is always recommended to replace the water pump whenever the mechanic already has these components removed for regularly scheduled timing belt replacement.

How do mechanics replace the water pump?

  • The water pump is usually bolted to the front of the engine. The replacement procedure will vary depending on whether the pump is driven by the timing belt, the serpentine belt, or chain.
  • On a cold engine, the engine coolant is drained to a level below the water pump.
  • Components that require removing to access the water pump are removed, including the belt or chain that directly drive the pump.
  • The bolts holding the pump to the engine are removed and the pump is pulled out.
  • The gasket surface must be cleaned and the pump mounting surface inspected. A new gasket, rubber seal, or RTV sealant, as required, is installed and then the new pump. The bolts are torqued in sequence using a calibrated inch pound torque wrench.
  • For applications where the water pump is driven by the timing belt, the timing belt must be removed. Typically, this requires removal of the crankshaft pulley, timing belt covers, and timing belt tensioner. Once the new pump is installed, new coolant is added back while bleeding the cooling system of any air. The engine is then run and brought to normal operating temperature to check for leaks and ensure normal operating temperature.

Is it safe to drive with a water pump problem?

No. Should the water pump only leak a little bit, you can drive the car. However, a small leak could suddenly enlarge or the pump bearing might unexpectedly seize. Either circumstance would likely cause engine overheating. If a defective water pump causes the overheating, it is not safe to drive because of the damage to the engine.

When replacing the water pump keep in mind:

  • It is best to install a new cooling system thermostat when you install a new water pump, especially if the thermostat is old or original.
  • Completely flushing the cooling system is a good idea when you replace the water pump. Flushing can be done before or after pump replacement.
  • The rest of the cooling system should be inspected too — particularly rubber hoses, which have a limited lifetime.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(4)

Rating Summary
3
0
0
1
0
3
0
0
1
0

Excellent Rating

(4)

Rating Summary
3
0
0
1
0
3
0
0
1
0
Number of Dodge Ram 1500 Van Water Pump Replacement services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

How to Buy a Good Quality Fuel Filter
Fuel Fuel filters can be considered the final defense to block particles that may be in the fuel from reaching and damaging the engine. Both high-pressure fuel injected systems with either diesel or gas fuel can all have additives or...
P2013 OBD-II Trouble Code: Intake Manifold Runner Control Circut High Bank 2
P2013 P2013 trouble code definition The P2013 trouble code is a generic DTC that indicates a malfunction within the intake manifold runner control circuit. This code is similar to P2005, P2006, P2007, P2008, P2008, P2010 and P2015. What the P2013...
How Do Underbody Car Lights Work?
Your Your car has a number of important lights on it – headlights, turn signals, taillights, brake lights, running lights, and more. However, your options aren’t limited to what was installed by the automaker. You can install aftermarket taillights and...

Coil pack keeps cracking.

The ignition coils are only meant to withstand a high electrical charge whereas the spark plugs can withstand that as well as the explosions within the combustion chamber. It is possible that you could have a small crack in your...

Metal-on-metal sound from front of car

It sounds like the pads are grinding the rotorLook through the wheel. Take note of the brake pad thickness. See if there is approximately 2mm of pad surface remaining (about the thickness of a nickel). If possible look at the...

Hearing clicking from wheel housing while turning

Hi. A clicking noise while turning in a front wheel drive car is usually caused by damaged or worn CV joints (https://www.yourmechanic.com/services/axle-cv-shaft-assembly-replacement). CV joints are mounted on each end of a front axle and they transfer power to the wheels...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com