Dodge Dakota Car Thermostat Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(16)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(16)

Car Thermostat Replacement Service

How much does a Car Thermostat Replacement cost?

On average, the cost for a Dodge Dakota Car Thermostat Replacement is $203 with $63 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1996 Dodge DakotaV8-5.2LService typeCar Thermostat ReplacementEstimate$339.80Shop/Dealer Price$386.09 - $516.03
2005 Dodge DakotaV6-3.7LService typeCar Thermostat ReplacementEstimate$328.99Shop/Dealer Price$376.57 - $515.20
1998 Dodge DakotaL4-2.5LService typeCar Thermostat ReplacementEstimate$314.93Shop/Dealer Price$359.02 - $487.12
2007 Dodge DakotaV6-3.7LService typeCar Thermostat ReplacementEstimate$328.99Shop/Dealer Price$376.60 - $515.24
1990 Dodge DakotaV6-3.9LService typeCar Thermostat ReplacementEstimate$315.29Shop/Dealer Price$360.95 - $490.42
2001 Dodge DakotaL4-2.5LService typeCar Thermostat ReplacementEstimate$314.93Shop/Dealer Price$359.16 - $487.37
1997 Dodge DakotaL4-2.5LService typeCar Thermostat ReplacementEstimate$314.93Shop/Dealer Price$359.04 - $487.15
2010 Dodge DakotaV6-3.7LService typeCar Thermostat ReplacementEstimate$328.99Shop/Dealer Price$376.60 - $515.24
Show example Dodge Dakota Car Thermostat Replacement prices

What is an engine cooling system thermostat and how does it work?

The car's engine cooling system thermostat is a small valve within a cooling system passageway that opens and closes in response to the temperature of the circulating engine coolant. When your car is first started and the coolant is cold, the valve in the thermostat will be in the closed position, circulating the coolant flow only within the engine instead of flowing to the radiator, which allows the engine to warm up fast, promoting fuel efficiency, low emissions, and reduced engine deposits. Once the engine coolant reaches the design temperature, usually around 195 degrees, the valve will open and close as you drive in order to maintain a coolant temperature typically between 195 to 225 degrees Fahrenheit.

Thermostat

When to consider replacing the engine cooling system thermostat:

  • Engine overheats. A thermostat with the valve stuck closed is a common cause of engine overheating. However, since there are other causes of overheating, a mechanic will thoroughly inspect the cooling system prior to condemning the thermostat. Since it is usually not known how badly the engine overheated, the mechanic will also try to determine if there is evidence that the cylinder head gasket was blown. If so, it would be repaired prior to replacing the thermostat.
  • Temperature gauge reads too low or too high. Thermostats can get sticky, causing the engine temperature to stray from the optimal range. Your dash-mounted temperature gauge will notify you of this malfunction.
  • Cooling system repairs. All thermostats eventually fail. Therefore, if the cooling system is already open for major repairs, such as water pump or radiator replacement, it is recommended to install a new thermostat simply as insurance against future breakdown.

How do mechanics replace the engine cooling system thermostat?

  • Once the engine is completely cold, the radiator cap is loosened and enough coolant is drained from the radiator so the coolant level is below the thermostat housing.
  • The thermostat housing is removed and the thermostat and gasket are extracted. Note that some cars have more than one cooling system thermostat and both might need replacement.
  • All mounting surfaces on the thermostat housing are cleaned of old gasket material. A new gasket is applied and the thermostat is re-installed in the correct orientation and with the temperature sensing cylinder facing downward towards the engine.
  • The thermostat housing bolts are tightened to original equipment manufacturer (OEM) specifications using a calibrated inch-pound torque wrench.
  • The cooling system is refilled with the appropriate coolant type and the system is fully bled of all air.
  • The car engine is run until the normal operating temperature is reached, and while taking precautions with the hot coolant, the coolant level is rechecked while confirming there is flow through the radiator — either visually or with an infrared temperature gun. This will confirm the thermostat is open. Finally, the engine is checked for leaks.

Is it safe to drive with an engine cooling system thermostat problem?

No. If it has been determined that there is a thermostat problem, it should be repaired right away. Failure to do so can cause substantial and costly damage to the engine.

When replacing the engine cooling system thermostat keep in mind:

  • Engine overheating due to causes other than a faulty thermostat, will themselves damage a thermostat. Therefore, always replace the thermostat if the engine overheats, even if the thermostat was not the initial cause of the overheating.
  • The thermostat should be replaced anytime you have major work done on the coolant system. It is convenient and costs little during such repairs and insurance against future breakdown.
  • OEM thermostats are the best ones to use and you can request your mechanic to install only the OEM thermostat. Dealer supplied, OEM thermostats are sometimes more costly but are generally higher quality and specifically engineered for your car.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(16)

Rating Summary
16
0
0
0
0
16
0
0
0
0

Clarissa

21 years of experience
227 reviews
Clarissa
21 years of experience
Dakota 2003 - Thermostat - Garnet Valley, PA
Clarissa was on time and very professional. She explained everything. Job was done in a timely manner. No hidden charges. In fact the final bill was less than the estimate.

Chris

10 years of experience
31 reviews
Chris
10 years of experience
Dakota 2001 - Shock Absorber - Clearfield, UT
Chris was very friendly and professional

Pedro

7 years of experience
26 reviews
Pedro
7 years of experience
Dakota 1998 - Wheel Stud - Bakersfield, CA
Great worker

CURTIS

5 years of experience
8 reviews
CURTIS
5 years of experience
Dakota 2003 - AC Belt - Warrington, PA
great all around

Excellent Rating

(16)

Rating Summary
16
0
0
0
0
16
0
0
0
0
Number of Dodge Dakota Car Thermostat Replacement services completed
176+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

How to Replace a Steering Damper
Steering dampers, also known as steering stabilizers or spirit dampers, prevent movement from traveling to the steering wheel.
The Guide To Colored Curb Zones in Wisconsin
Wisconsin Wisconsin parking laws: understanding the basics Drivers in Wisconsin should make it a point to learn and understand the various parking laws they have to abide by. Failure to adhere to the law when parking could mean a citation...
P0604 OBD-II Trouble Code: Internal Control RAM Error
P0604 means an indication of an internal memory fault which may be cause by a faulty fuse, low battery or faulty ECM power supply circuit wiring.

Exhaust leak causing clicking sound.

Yes, this could be the cause, you may have a leak at one of the exhaust manifold tubes. The exhaust manifolds needs to be inspected for a black soot buildup at the joining surface of the cylinder head and exhaust...

steering column shaft is hitting the wall to the left and right when turning.

Hi there. Check the locking pin to the steering column shaft and make sure that it is locking to the input shaft to the rack and pinion gear set. If the lock is engaged and the shaft is coming off...

Loud clicking sound coming from where the serpentine belt is when car is running

Hi there. In most cases, this type of clicking sound is caused by a belt that is slightly frayed and hitting a shield or other mechanical component. It's also common for a worn out pulley or idler tension pulley to...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com