Buick Envision Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(4)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(4)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Buick Envision Brake Drum Replacement is $322 with $208 for parts and $114 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 Buick EnvisionL4-2.0L TurboService typeBrake Drum ReplacementEstimate$577.15Shop/Dealer Price$695.19 - $1017.81
2018 Buick EnvisionL4-2.0L TurboService typeBrake Drum ReplacementEstimate$530.15Shop/Dealer Price$646.21 - $967.35
2019 Buick EnvisionL4-2.5LService typeBrake Drum ReplacementEstimate$577.64Shop/Dealer Price$698.71 - $1023.61
2017 Buick EnvisionL4-2.5LService typeBrake Drum ReplacementEstimate$549.15Shop/Dealer Price$667.18 - $989.79
2016 Buick EnvisionL4-2.0L TurboService typeBrake Drum ReplacementEstimate$549.15Shop/Dealer Price$667.23 - $989.89
2018 Buick EnvisionL4-2.5LService typeBrake Drum ReplacementEstimate$530.15Shop/Dealer Price$646.21 - $967.34
2019 Buick EnvisionL4-2.0L TurboService typeBrake Drum ReplacementEstimate$586.14Shop/Dealer Price$706.98 - $1031.70
Show example Buick Envision Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Buick mechanics

Real customer reviews from Buick owners like you.

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0

Alex

20 years of experience
138 reviews
Alex
20 years of experience
Buick Envision L4-2.0L Turbo - Car is not starting - Crest Hill, Illinois
Very professional. In and out. Great job. Thank You

James

30 years of experience
904 reviews
James
30 years of experience
Buick Envision L4-2.0L Turbo - Door does not lock or open Inspection - Winter Garden, Florida
Amazing and super friendly. Very knowledgeable and enjoyed his time

Collins

12 years of experience
513 reviews
Collins
12 years of experience
Buick Envision L4-2.5L - Oil Change - Atlanta, Georgia
Punctual. Collins did a great job! Look forward to booking again.

Nick

7 years of experience
12 reviews
Nick
7 years of experience
Buick Envision L4-2.5L - Windshield Washer Pump Replacement (Front) - Houston, Texas
Came early, fixed the problem, in and out in a jiffy!

Excellent Rating

(4)

Rating Summary
4
0
0
0
0
4
0
0
0
0
Number of Buick Envision services completed
44+
services done by our mechanics
TOTAL NUMBER OF EXPERT Buick MECHANICS
800+
experts on our platform

Recent articles & questions

A Buyer’s Guide to the 2012 Mini Cooper Hardtop
Key Key Features The standard 1.6 liter in-line four cylinder engine offers 121 horsepower at 6,000 rpm. While driving in the city, expect to get around 29 mpg while the driving on the highway will get you around 37 mpg....
How to Transfer a Car Title in Rhode Island
A A car title is the document that proves ownership of a particular vehicle. However, when that ownership changes, whether through a sale, a donation, or through inheritance, the title must be updated to reflect the new situation. This is...
The Traveler’s Guide to Driving in Hong Kong
Hong Hong Kong is a fantastic place to take a vacation. There are many fascinating things that you can see and do (https://www.expedia.com/things-to-do/?location=Hong-Kong&regionId=184245&semcid=US.MULTILOB.BING.SEARCH.TSHOP&kword=things_to_do_in_hong_kong!e.ZzZz.4340000028701.0.10583933646.things%20to%20do%20in%20hong%20kong.things_to_do_in_hong_kong&utm_source=bing&utm_medium=cpc&utm_campaign=USA%3AENG%3AFAR_EAST%3ADT%3A%5D&utm_term=things%20to%20do%20in%20hong%20kong&utm_content=USA%3AHKG%3ADT%3A%5D%3AXX%3AHong_Kong%3A77%3AHong_Kong%3A184245%3AX%3Athings_to_do) in this tourist friendly city. You could visit Madame Tussauds, Ocean Park, Disneyland, and other entertainment venues....

Car won't pass smog check

Hi there. Your smog check is measured as to how efficiently your vehicle is burning fuel and air. Smog is reliant on many different components. Your EGR valve, vacuum, and also your catalytic converter are factored in. I would strongly...

Popping noise, wheels won't turn

For your 2001 Chrysler LHS, the inner tie rods (https://www.yourmechanic.com/services/tie-rod-end-replacement) are attached to the steering gear with a retaining bolt and a lock tab. If the bolts are not torqued enough and the lock tab engaged, the bolts can back...

When idling my car overheats?

Claimed by John Hege

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com