Popular articles

P2652 P2652 code definition B Rocker Arm Actuator System Stuck On Bank1 What the P2652 code means The Engine control module (ECM) has a wide variety of jobs, but one of the most critical is to keep the supply of...

A car horn uses a horn relay to power it and make sound. A faulty relay can be replaced by safely disconnecting the old one and plugging in a new one.

Trouble code P0332 means the PCM is receiving a reading that the knock sensor is too low, which can result in higher emissions and engine problems.

P2282 P2282 code definition Air Leak Between Throttle Body and Intake Valves What the P2282 code means P2282 is an OBD-II generic code for the engine control module (ECM) monitoring the vacuum in the intake manifold at idle. This code...

The The role of your vehicle’s windshield washer pump is to take the washer fluid from the reservoir and circulate it through the tubes to the car’s windshield washer nozzles. The nozzles then spray the washer fluid on your car’s...

If your car is riding lower than usual, making abnormal sounds, and its compressor won't start, you may need to replace the air suspension compressor.

Drum Drum brakes are a very common braking option used on many vehicles today. While disc brakes have become the standard for use on the front and rear axles of many vehicles, drum brakes are still very commonly used. However,...

P0481 means a problem with the control circuit for cooling fan 2. Some causes are faulty cooling fan or damage to the wire connecting the cooling fan.

Flat tires are an inevitable part of owning a car. Changing a flat tire can be difficult and requires several...

Find the common reasons why your car may be overheating and discover practical solutions to check and fix the issue with YourMechanic.

Common signs include clunking or clicking sounds, jerking movements in the steering wheel, and inconsistent steering.

The hood struts, or lift support, support your vehicle's hood while you access the engine compartment. A failed strut is a safety concern.

P2757 means a problem with the torque converter clutch pressure control solenoid due to a bad torque converter or solenoid or electrical issues.

P0777 code means a fault was detected in either the electronic pressure control solenoids or solenoid circuits often due too failures or blockages.

Valve cover gasket leaks usually start when not much oil leaves the engine. It should be repaired before it causes serious damage and costly repairs.

The axles transmit power from either the transmission or the differential to the drive wheels on your car. If one of your...

P2651 means an electrical circuit that is short or open in the rocker arm actuator control circuit due to low engine oil or an open circuit.

What What the P2272 code means? P2272 is an OBD-II generic code for the engine control module (ECM) detecting the O2 sensor for bank 2 sensor 2 after the catalytic convertor is stuck lean. What causes the P2272 code? ...

P0190 trouble code definition Fuel rail pressure sensor circuit malfunction What the P0190 code means The power control module (PCM) has detected...

Common signs include inaccurate oil readings, the Oil Light coming on for no reason, the car not starting, and the Check Engine Light coming on.

The fuel system has a fuel rail sensor which fails when the engine operates erratically, has difficulty starting, or the Check Engine Light comes on.

P0842 P0842 code definition The P0842 code indicates that there has been an abnormally high voltage reading from the transmission fluid pressure sensor circuit. Other shift solenoid, transmission slippage, lock up, gear ratio, or torque converter clutch codes are often...

When When you purchase a vehicle, you're supposed to receive a title showing transfer of ownership. Several types of titles exist, and you need to understand the difference between a clean title and salvage title before you buy a used...

A faulty secondary air injection pump can result in increased emissions, engine performance issues, and an illuminated Check Engine Light.

P0711 P0711 code definition The P0711 code is a generic powertrain code related to the transmission, including sensor failures and pressure faults. In this case, it means that the engine control module (ECM) or powertrain control module (PCM) has detected...