Mercury Grand Marquis Power Steering Pressure Hose Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(357)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(357)

Power Steering Pressure Hose Replacement Service

How much does a Power Steering Pressure Hose Replacement cost?

On average, the cost for a Mercury Grand Marquis Power Steering Pressure Hose Replacement is $180 with $40 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2008 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$460.52Shop/Dealer Price$519.41 - $683.12
1996 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$461.95Shop/Dealer Price$542.77 - $781.12
1992 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$389.17Shop/Dealer Price$451.82 - $635.60
2003 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$591.26Shop/Dealer Price$683.66 - $954.15
1994 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$461.95Shop/Dealer Price$544.27 - $783.74
2005 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$446.10Shop/Dealer Price$502.43 - $664.22
2011 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$446.10Shop/Dealer Price$502.23 - $663.87
2004 Mercury Grand MarquisV8-4.6LService typePower Steering Pressure Hose ReplacementEstimate$446.10Shop/Dealer Price$502.21 - $663.83
Show example Mercury Grand Marquis Power Steering Pressure Hose Replacement prices

What is the power steering pressure hose and how does it work?

The power steering pressure hose transfers the high-pressure hydraulic output of the power steering pump to either a steering gear box or steering rack and pinion unit to create the power assist that you rely on when you turn the steering wheel. The pressure hose is only used in cars with a power steering pump and reservoir, so if you have a newer car you may have electric power steering instead. The pressure hose is relatively large in diameter in order to withstand high hydraulic pressure, flex as the engine moves and vibrates, and also withstand engine heat, accidental cuts, and abrasion.

When to the consider replacing the power steering pressure hose:

  • Groaning, whirring noise or difficulty steering. Noise, or difficulty turning the steering wheel, may reflect a low power steering fluid level, which could be due to a leak in a pressure hose, or a leak elsewhere in the power steering system. Although a leak in the pressure hose is a possible cause of a low fluid level, a mechanic will consider all other possible causes, too.
  • Visible fluid leaks. There are usually steel ferrules clamped onto each end of the rubber pressure hose. These ferrules are common leak points. If there is seepage from these ferrules, the pressure hose should be replaced.
  • Hose damage. If the hose has significant physical damage, such as cuts, abrasions, cracks, or heat damage, the hose should be replaced to avoid sudden hose failure.
  • Contaminated fluid. If rubber particles are found in the power steering fluid or reservoir, it means the interior of either the pressure hose or the return hose is deteriorating. All rubber hoses should be replaced and the system flushed. An in-line, aftermarket fluid filter might be required.
  • Hose age. Both the pressure and return hoses are rubber-based products with a limited service life. If the vehicle is more than 10 years old, and power steering components are being replaced, all the rubber hoses should be replaced during that service.

How do mechanics replace the power steering pressure hose?

The underhood routing of the power steering pressure hose varies greatly between car models. The repair procedure ranges from simple to quite involved. The basic steps are:

  • Raise car as needed and support with steel safety stands.
  • Unthread the pressure hose tube nuts, or banjo-style bolts, at each end of the pressure hose.
  • Remove pressure hose and inspect interior hose lining for separation, if visible.
  • Install a new hose, using a new sealing washer or O-ring seals as applicable, and paying particular attention to the required original equipment manufacturer’s (OEM) torque value for the tube nuts or banjo bolts. Replace rubber return hose, if required, and with the authorization of the customer.
  • Once the system is fully sealed again, bleed or flush power steering system as required to remove all air and contaminants.
  • Finally, the engine is run, the car is test driven, and leaks are checked for at all connections.

Is it safe to drive with a power steering pressure hose problem?

No. The fluid in the power steering pressure hose is under very high pressure and flammable. A leak that sprays fluid into a hot engine part, such as the exhaust manifold, can cause a fire. Leaks that cause significant fluid loss can cause difficulty in steering and, if a leak causes the fluid level in the reservoir to drop too low, it can cause damage to the power steering pump too, necessitating the installation of not only a new hose but a new pump.

When replacing the power steering pressure hose keep in mind:

  • When the power steering hoses are replaced, the entire power steering system should be inspected.
  • Use only OEM specified power steering fluid in your power steering system.
  • If the pressure hose has deteriorated from the inside, the rubber return hose should be replaced as well and the system should be flushed. A mechanic might recommend the installation of an in-line filter to capture all debris.
  • Tube nuts and banjo bolts used to seal pressure hoses have OEM-specified torque values. Mechanics will use a calibrated torque wrench to tighten the connections.
  • Complete removal of air from the system can occasionally take some time, even after the normal bleeding procedure. During this time some mild noise may be heard when turning the steering wheel. If it persists more than a day or so, the system should be rechecked.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(357)

Rating Summary
336
12
3
2
4
336
12
3
2
4

Chris

10 years of experience
31 reviews
Chris
10 years of experience
Grand Marquis 2002 - Tie Rod End - Salt Lake City, UT
Doesn't leave work unfinished, in my case he had to go get a part and a specific tool to finish thhe job.

Chris

10 years of experience
31 reviews
Chris
10 years of experience
Grand Marquis 2002 - Brake Pads - Salt Lake City, UT
Very thorough. Nice guy, does good work.

Jason

0 years of experience
417 reviews
Jason
0 years of experience
Grand Marquis 2001 - Air Spring Bag - Phoenix, AZ
came and took care of problem great guy

LAVELL

26 years of experience
129 reviews
LAVELL
26 years of experience
Grand Marquis 2001 - Check Engine Light is on - Oakland, CA
I was pleasantly surprised he was able to show up early. I wish I could figure out what the problem is, but he told me not to worry much and call for an appt if the light comes on again.

Excellent Rating

(357)

Rating Summary
336
12
3
2
4
336
12
3
2
4
Number of Mercury Grand Marquis services completed
3927+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

P2035 OBD-II Trouble Code: Exhaust Gas Temperature (EGT) Sensor Circuit Low Voltage Bank 2 Sensor 2
P2035 P2035 code definition Exhaust Gas Temperature (EGT) Sensor Circuit Low Voltage Bank 2 Sensor 2 Bank 2 refers to the back of cylinders without the number one cylinder. Sensor 2 would be the second EGT sensor from the motor...
How Does a Push-Button Start Work?
For the vast majority of people, cranking your car involves getting the key out, sliding it into the ignition, and turning...
Top Automotive News & Stories – September 3-9
This week's top auto news: Ford's 3D printed future, Dieselgate guilty plea, Toyota Supra prototype spied, LaFerrari Aperta on the road, and more.

Where is the downhill assist control operation in a car and how is it built?

Hi There, Although this application may vary depending on your specific type of vehicle, generally they all work similarly. The Downhill assist control (commonly referred to as DAC) is a system that helps to control the vehicle without manual operation...

03 buick lasebre custom

Hi There, It sounds like you may have a dirty or failing idle air control valve causing your engine idle to fluctuate. The idle air control valve (https://www.yourmechanic.com/services/idle-control-valve-replacement) is a small valve on the engine's intake system that reads the...

Question about 1999 isuzu rodeo transmission

Hi there. Unfortunately, this is not a compatible fit for a 1999 Isuzu Rodeo. It's always recommended to replace any component with the same parts from a similar year, make and model.

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com