Mercury Cyclone Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(1,383)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(1,383)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Mercury Cyclone Brake Drum Replacement is $454 with $226 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1964 Mercury CycloneV8-4.3LService typeBrake Drum ReplacementEstimate$727.96Shop/Dealer Price$864.95 - $1221.94
1970 Mercury CycloneV8-5.8LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$817.00 - $1174.02
1971 Mercury CycloneV8-7.0LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$816.99 - $1174.01
1965 Mercury CycloneV8-4.7LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$816.94 - $1173.92
1969 Mercury CycloneV8-5.0LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$817.03 - $1174.08
1968 Mercury CycloneV8-5.0LService typeBrake Drum ReplacementEstimate$679.96Shop/Dealer Price$816.99 - $1174.01
1971 Mercury CycloneV8-5.8LService typeBrake Drum ReplacementEstimate$691.96Shop/Dealer Price$828.67 - $1185.44
1964 Mercury CycloneV8-7.0LService typeBrake Drum ReplacementEstimate$691.96Shop/Dealer Price$829.56 - $1187.00
Show example Mercury Cyclone Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Mercury mechanics

Real customer reviews from Mercury owners like you.

Excellent Rating

(1,383)

Rating Summary
1,297
50
9
6
21
1,297
50
9
6
21

Frank

30 years of experience
60 reviews
Frank
30 years of experience
Mercury Sable V6-3.0L - Starter - Nashville, Tennessee
I was more than happy with the experience. Was more like having a good friend show up to help you, rather than a total stranger. Very friendly, courteous, and a very skilled mechanic. Am recommending him to all of my friends.

Roland

17 years of experience
27 reviews
Roland
17 years of experience
Mercury Sable V6-3.0L - Oil Change - Fort Myers, Florida
Outstanding. Roland arrived a few minutes before the scheduled time. Rang my bell and introduced himself. I took him to the car which was in my garage. He proceeded to bring in his equipment and when set-up, he began. Besides the work I contracted for he looked over the entire vehicle and pointed out several items that needed to be watched. He was extremely pleasant and he cleaned up after himself and when done, I would never had known he was there .... he left the garage spotless. I'm extremely impressed with his professionalism and his expertise. I would highly recommend his services.

Noe

36 years of experience
604 reviews
Noe
36 years of experience
Mercury Grand Marquis V8-5.0L - Distributor Rotor and Cap - Seattle, Washington
Noe is a good mechanic. He worked on my 1985 Mercury Grand Marquis. He is knowledgeable and competent. He answered my questions and offered good advise on my car's maintenance. He allowed me to observe him servicing my car. He was friendly and polite. I will use his services again in the future! A+

Frank

40 years of experience
57 reviews
Frank
40 years of experience
Mercury Grand Marquis V8-4.6L - Coolant is leaking - Woodstock, Georgia
Great experience

Excellent Rating

(1,383)

Rating Summary
1,297
50
9
6
21
1,297
50
9
6
21
Number of Mercury services completed
15213+
services done by our mechanics
TOTAL NUMBER OF EXPERT Mercury MECHANICS
600+
experts on our platform

Recent articles & questions

How Often Do I Need to Replace My Car's Differential Fluid?
Many folks do not even know what the differential does. It is not one of those common car parts like the transmission or...
P0003 OBD-II Trouble Code: Fuel Volume Regulator Control Circuit Low
P0003 P0003 trouble code definition The P0003 code is associated with the electrical circuit which connects to your fuel pressure regulator. It also may be related to other codes, such as: P0001, P0002, or P0004. What the P0003 code means...
How to Buy a Personalized License Plate in Kentucky
Adding Adding a personalized license plate can be a fun way to add a unique touch to your vehicle. You can use a personalized license plate to say something important to you, such as the name of your dog or...

Is there a way to tell if engine oil was placed in the transmission by mistake?

Hello. Technically, yes, it can be proven by chemical analysis. This would most likely have to be a forensic investigation so obviously you would have to send a sample of the fluid to a laboratory that has a capability in...

What could b wrong if when I het to 55 mph and then push the gas the car vibrates. But when I let up on the gas it's fine. And the

The vibration and shaking when accelerating may be a transmission shift issue or the engine is misfiring under a load. The shaking when braking may be due to warped brake rotors. You should have the computer scanned for misfire or...

1994 Ford Taurus will not start after battery/starter replacement

You may have a starter relay that needs replaced or the neutral safety switch on transmission can be cause. The start relay needs to be checked to see if it is getting power to small terminal when trying to crank...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com