Jeep J-210 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep J-210 Brake Drum Replacement is $453 with $225 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1965 Jeep J-210L6-3.8LService typeBrake Drum ReplacementEstimate$726.44Shop/Dealer Price$863.05 - $1218.90
1964 Jeep J-210L6-3.8LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.10 - $1170.98
1963 Jeep J-210L6-3.8LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.09 - $1170.97
1965 Jeep J-210V8-5.3LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.04 - $1170.88
Show example Jeep J-210 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0

Shaun

21 years of experience
204 reviews
Shaun
21 years of experience
Jeep Compass L4-2.4L - Brake Drum - Walnut Creek, California
Shaun helped me not just replaced brake drum but also find a issue with my brake cylinder. So he helped me replaced brake cylinder too.

Armando

32 years of experience
33 reviews
Armando
32 years of experience
Jeep Patriot L4-2.4L - Brake Drum - San Marcos, California
Armando was knowledgeable, courteous, and on-time. He actually let me know that some of the services I requested were unnecessary, which speaks volumes about him, and YourMechanic. Lifetime customer here!

Victor

11 years of experience
211 reviews
Victor
11 years of experience
Jeep Wrangler L6-4.0L - Brake Drum - Virginia Beach, Virginia
Very personable. Great attitude and answered all of my questions/concerns. Very highly recommended! He did a great job.

Daniel

11 years of experience
229 reviews
Daniel
11 years of experience
Jeep Wrangler L4-2.5L - Brake Drum - Villa Park, Illinois
Great mechanic!

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0
Number of Jeep Brake Drum Replacement services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Jeep MECHANICS
1300+
experts on our platform

Recent articles & questions

How to Buy a Good Quality Heater Blower Motor Resistor
Vehicles Vehicles that are equipped with a manual HVAC, or climate control, system utilize a blower motor resistor to control the speed of the heater blower. If you are driving a minivan or an SUV with a separate rear passenger...
How to Remove Cylinder Head Bolts
Removing Removing the head is a major step in removing the cylinder head (https://www.yourmechanic.com/article/how-to-buy-a-good-quality-cylinder-head). These head bolts hold the cylinder head to the engine block. The head bolts are long bolts that go through the cylinder head and head gasket...
A Day in the Life of a YourMechanic Mobile Technician
Mark Lenhart has been a mobile technician with YourMechanic since 2014. Follow Mark's day as he repairs transmissions and diagnoses leaking fluids.

Engine chugging at low speeds when the weather is bad

It is very possible that moisture is getting into the connectors of the engine control module (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-engine-control-module-ecm). The connectors should be checked and cleaned if necessary. Di-electric grease can be used to help seal the connectors and keep the moisture...

Will a spare tire on the front of the car cause next to brake badly?

Hi, and thank you for your question. When you have an issue with a flat and need to replace it with a donut tire, you will experience some difficulty when driving the vehicle (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-a-donut-tire). When putting the donut tire on...

My car overheated now it cranks and won't start no blown head gasket

If the car was out of coolant, and shut off because it was overheated, then there is a good chance that there was some engine damage. But don't panic yet, the codes and leaks you have might be separate issues...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com