Jeep J-100 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(12)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(12)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Jeep J-100 Brake Drum Replacement is $453 with $225 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1971 Jeep J-100V8-5.7LService typeBrake Drum ReplacementEstimate$726.44Shop/Dealer Price$863.05 - $1218.90
1973 Jeep J-100L6-4.2LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.10 - $1170.98
1972 Jeep J-100L6-4.2LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.09 - $1170.97
1967 Jeep J-100V8-5.3LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.04 - $1170.88
1964 Jeep J-100L6-3.8LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.13 - $1171.04
1969 Jeep J-100L6-3.8LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.09 - $1170.97
1972 Jeep J-100V8-5.9LService typeBrake Drum ReplacementEstimate$690.44Shop/Dealer Price$826.77 - $1182.40
1967 Jeep J-100L6-3.8LService typeBrake Drum ReplacementEstimate$690.44Shop/Dealer Price$827.66 - $1183.96
Show example Jeep J-100 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Jeep mechanics

Real customer reviews from Jeep owners like you.

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0

Peter

25 years of experience
519 reviews
Peter
25 years of experience
Jeep Patriot L4-2.0L - Brake Drum - Sylmar, California
Peter was amazing and really informative on what my car needed. He arrived on time and was quick to get the work done. I definitely recommend him to anyone needing a great mechanic!

Brent

14 years of experience
10 reviews
Brent
14 years of experience
Jeep Patriot L4-2.4L - Brake Drum - Tempe, Arizona
Amazing job, knowlegeable about what he was doing

Armando

32 years of experience
33 reviews
Armando
32 years of experience
Jeep Patriot L4-2.4L - Brake Drum - San Marcos, California
Armando was knowledgeable, courteous, and on-time. He actually let me know that some of the services I requested were unnecessary, which speaks volumes about him, and YourMechanic. Lifetime customer here!

Lucas

21 years of experience
885 reviews
Lucas
21 years of experience
Jeep Patriot L4-2.4L - Brake Drum - Los Angeles, California
Although there seemed to be a little confusion surrounding the parts, Lucas's personality and dedication to getting the job done made it a enjoyable experience. Lucas is great!!!

Excellent Rating

(12)

Rating Summary
12
0
0
0
0
12
0
0
0
0
Number of Jeep Brake Drum Replacement services completed
132+
services done by our mechanics
TOTAL NUMBER OF EXPERT Jeep MECHANICS
1300+
experts on our platform

Recent articles & questions

How Long Does a Windshield Wiper Module Last?
Most Most of the modern cars on the market are equipped with a number of electronic components. Finding a way to keep up with them all is not nearly as easy as it sound. In order for these parts of...
What is a VIN and Where Can I Find It?
The Vehicle Identification Number, or VIN, includes specific information about your car, including the model year, engine code, and country of origin.
What Does the Airbag Warning Light Mean?
When the airbag warning light stays on, the airbags won't deploy for seated passengers in a collision. This could be due to a sensor issue.

Car won't turn over

Hi. A bad fuel pump or clogged filter will keep your car from running, but not from turning over. The low battery might be the reason the car does not turn over. A charged battery will be necessary to properly...

p0303, p1313, p0420. codes come up. no flashing and now signs. what do I do?

Hi there. Sounds like there are a few things going on. First the code P1313 (http://obdii.pro/en/code/P1313) means that the timing chain (https://www.yourmechanic.com/services/timing-chain-replacement) has jumped a tooth making the camshaft and crankshaft out of sync. The chain tensioner may need replaced...

1996 Olds Aurora OBDII P0603 PCM keep alive memory, car is in limp mode and running like it's off timing

Correct the ground connection first, in case that problem is a cause of the trouble code. P0603 does represent an electrical system fault. In practice, this particular fault might be found as battery terminal corrosion or loose connections, Keep Alive...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com