Ford Econoline Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(24)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(24)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ford Econoline Brake Drum Replacement is $459 with $231 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1965 Ford EconolineL6-2.8LService typeBrake Drum ReplacementEstimate$901.72Shop/Dealer Price$1082.15 - $1569.46
1966 Ford EconolineL6-2.8LService typeBrake Drum ReplacementEstimate$853.72Shop/Dealer Price$1034.20 - $1521.54
1963 Ford EconolineL6-2.4LService typeBrake Drum ReplacementEstimate$690.32Shop/Dealer Price$829.94 - $1194.73
1962 Ford EconolineL6-2.4LService typeBrake Drum ReplacementEstimate$690.32Shop/Dealer Price$829.89 - $1194.64
1963 Ford EconolineL6-2.8LService typeBrake Drum ReplacementEstimate$853.72Shop/Dealer Price$1034.23 - $1521.60
1967 Ford EconolineL6-3.9LService typeBrake Drum ReplacementEstimate$740.40Shop/Dealer Price$892.54 - $1294.89
1964 Ford EconolineL6-2.8LService typeBrake Drum ReplacementEstimate$865.72Shop/Dealer Price$1045.87 - $1532.96
1961 Ford EconolineL6-2.4LService typeBrake Drum ReplacementEstimate$702.32Shop/Dealer Price$842.51 - $1207.72
Show example Ford Econoline Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(24)

Rating Summary
24
0
0
0
0
24
0
0
0
0

Alex

22 years of experience
25 reviews
Alex
22 years of experience
Ford Transit-250 V6-3.7L - Brake Drum - Pomona, California
Alex did a great job. very professional and on time

Gerron

34 years of experience
185 reviews
Gerron
34 years of experience
Ford Escape V6-3.0L - Brake Drum - Portland, Oregon
He was professional and completed the job fairly quick.

Russell

24 years of experience
356 reviews
Russell
24 years of experience
Ford Ranger V6-4.0L - Brake Drum - Portland, Oregon
Russell Gindlesperger really helped to get my truck running correctly! I have never meet a more honest mechanic who really helped to make sure everything was fixed. I wish I had only been using Rus from Your Mechanic for years.

Refugio

17 years of experience
51 reviews
Refugio
17 years of experience
Ford Escape L4-2.3L - Brake Drum - San Antonio, Texas
Absolutely perfect job and regained the trust of my Mother-in-Law whose car he had worked on.

Excellent Rating

(24)

Rating Summary
24
0
0
0
0
24
0
0
0
0
Number of Ford Brake Drum Replacement services completed
264+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

How Long Does an Exterior Door Handle Last?
No No matter what make or model vehicle you drive, it has door handles. You have a door handle located on the inside of your car, as well as the outside. While we don’t often think of this as a...
How to Get a Smog Check
Smog checks are designed to help lower the emissions created by vehicles. The word “smog” refers to smoke and fog air pollution, which is created in large part by emissions from cars. While smog checks aren’t mandatory everywhere in the...
B1993 OBD-II Trouble Code: Driver Side Side-Mount Air Bag Circuit Short to Ground
Trouble code B1993 means that the PCM received a voltage signal from the side-mount air bag circuit. The SRS warning light may illuminate.

Car losing water, but I don't see the leak.

Hi and thanks for the question - it is a good one. Modern cooling systems work under different pressures and with so many hoses and auxiliary water pumps it can be hard to find a coolant leak. Factor in that...

Does the dipstick tube just pull out of the block or are there retaining clips?

To answer your first question: yes, it does have a bracket on the oil dipstick tube but, if you remove the bracket, it will pull out. Your dipstick is going to have some curves in it; this is normal for...

For a couple days now all the car will do is crank but not start.

Hi there. As you already know, replacing components without proper diagnoses, can be expensive and time consuming without resolution. Assuming, the engine is mechanically sound, turns over uniform with compression. This would lead me to believe, it could be no...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com