Ford E-250 Power Steering Pump Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(44)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(44)

Power Steering Pump Replacement Service

How much does a Power Steering Pump Replacement cost?

On average, the cost for a Ford E-250 Power Steering Pump Replacement is $280 with $98 for parts and $182 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2008 Ford E-250V8-5.4LService typePower Steering Pump ReplacementEstimate$482.22Shop/Dealer Price$557.08 - $771.13
2011 Ford E-250V8-4.6LService typePower Steering Pump ReplacementEstimate$692.13Shop/Dealer Price$820.10 - $1198.64
2004 Ford E-250V8-5.4LService typePower Steering Pump ReplacementEstimate$386.47Shop/Dealer Price$438.05 - $587.38
2007 Ford E-250V8-4.6LService typePower Steering Pump ReplacementEstimate$386.47Shop/Dealer Price$438.05 - $587.37
2006 Ford E-250V8-5.4LService typePower Steering Pump ReplacementEstimate$386.47Shop/Dealer Price$439.97 - $590.73
2012 Ford E-250V8-4.6LService typePower Steering Pump ReplacementEstimate$692.13Shop/Dealer Price$820.31 - $1199.01
2014 Ford E-250V8-5.4LService typePower Steering Pump ReplacementEstimate$692.13Shop/Dealer Price$820.15 - $1198.73
2003 Ford E-250V8-5.4LService typePower Steering Pump ReplacementEstimate$386.47Shop/Dealer Price$438.05 - $587.37
Show example Ford E-250 Power Steering Pump Replacement prices

What is the power steering pump and how does it work?

The power steering pump is a belt-driven or electric-driven hydraulic pump that generates the hydraulic pressure needed to provide power steering assist. It develops output pressures of 1,000 PSI or more. The pump output is directed to the steering gear, often a rack and pinion type unit, where the hydraulic pressure pushes on the steering rack, greatly reducing the effort it would otherwise take to turn the steering wheel.

Power Steering

When to consider replacing the power steering pump:

  • Groaning or whining noise when turning. Noise can occur if there is wear on the pump bearings or impeller vanes. A low fluid level or trapped air can also cause noises. If the pump has already been operating while dry, adding fluid may not resolve the noise and replacement of the pump might be necessary.
  • Power steering fluid leaks. Leaks can develop at pump seals, threaded connections, hoses, or on the steering rack and pinion unit. Pump seal leaks will generally require a replacement.
  • Difficult steering. Should you notice it is harder to turn the steering wheel, it might mean the power steering pump output pressure is too low, or there could be blockages in the pump or lines.
  • Damage to the pump pulley. Should the pump pulley become damaged or is loose on the pump shaft, you might detect vibration, drive belt damage, or hard steering. Either the pulley will have to be serviced or the pump assembly replaced.

How do mechanics replace the power steering pump?

  • If driven by a drive belt, the power steering pump is bolted to the engine via a bracket that allows for adjustment of the pump drive belt. Once the engine is cold, and safe to work on, the drive belt is removed.
  • If driven by an electric pump, the pump may be mounted in conjunction with the steering shaft or in conjunction with the steering rack. With either a drive belt or electric pump, removal of any dash, panel, or steering components is performed to access the pump.
  • The threaded connectors to the pump inlet and outlet are loosened and removed.
  • Any mounting bolts and brackets are removed so the pump can be removed.
  • If the old pump has failed catastrophically, or there is reason to suspect contaminants in the power steering hoses, the system is flushed.
  • The new pump is bolted on, the pressure and return hoses attached and the system is bled of all air. If pump is belt-driven, it is tightened to the manufacturer’s specification.
  • Finally, the engine is run and the car is road tested to confirm normal steering effort. If a new drive belt was installed, belt tension is measured again, and adjusted as needed, after the belt has run for a few minutes.

Is it safe to drive with a power steering pump problem?

No. If the power steering pump is operated without an adequate amount of fluid, and the pump reservoir will not hold fluid due to a large leak. The pump could seize, which would snap the serpentine belt and likely leave you stranded. If the pump turns and there is adequate fluid, but there is no power assist, it will require much greater effort to turn the steering wheel, and that presents inherent safety risks. Generally, the wisest course is to seek immediate repairs if you suspect a problem with any component in your car’s power steering system.

When replacing the power steering pump keep in mind:

  • Any belts driving the pump should be inspected and replaced as needed. The pump will only produce the required hydraulic pressure if it is driven by the belt at an adequate speed.
  • Power steering leaks from aged rubber hoses, particularly where the rubber is crimped to the steel tube, are not unusual and should be carefully inspected. The system operates under high pressure. The fluid is flammable, and if leaking fluid happens to contact a hot engine part, a fire might result. You always want to be sure the hoses and connections are sound.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(44)

Rating Summary
43
0
0
0
1
43
0
0
0
1

Jonathan

25 years of experience
42 reviews
Jonathan
25 years of experience
E-250 2008 - Starter - Marietta, GA
Jonathan showed up on time and did a good job installing a new starter!

Larry

18 years of experience
54 reviews
Larry
18 years of experience
E-250 2011 - Brake Pads - Hayward, CA
Excellent service. Larry did rear brakes on our E250 van, really nice guy, punctual and great work. Honest assessment of work needed.

Leslie

10 years of experience
84 reviews
Leslie
10 years of experience
E-250 2004 - Serpentine/Drive Belt - Philadelphia, PA
Great service

Graham

14 years of experience
132 reviews
Graham
14 years of experience
E-250 2003 - Steering Rack/Gearbox - Streamwood, IL
Very polite. Explained everything Cleaned up and removed old fluid.

Excellent Rating

(44)

Rating Summary
43
0
0
0
1
43
0
0
0
1
Number of Ford E-250 services completed
484+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1800+
experts on our platform

Recent articles & questions

How to Renew Your Car Registration in South Carolina
Having Having your car registered with the South Carolina DMV is vital to driving legally in this state. There are a variety of different fines that you will be subjected to if you fail to make this happen. Once you...
Symptoms of a Bad or Failing Fog Light Switch
Common signs include fog lights that are dim, flickering, or not turning on at all, and a blown fog light fuse.
Understanding the Mercury Intelligent Oil Life Monitor and Service Indicator Lights
Car symbols, or dashboard lights, are a car service reminder. The Mercury Intelligent Oil Life Monitor indicates when and what service your car needs.

Tire valve stem base leaks air

From the description provided, it seems you have quite the leak coming from your Corolla’s tire. I would recommend taking your vehicle, or just the tire if you wish, to the nearest tire shop and have them replace the valve...

Po420 bank1

Hello Tom. P0420 (https://www.yourmechanic.com/services/check-engine-light-is-on-inspection) is the Catalyst System Efficiency Below Threshold (Bank 1) code. While there are a multitude of components that can cause this code, the general concept is that your catalytic converter is not working properly. If you...

It rattles when in idle. I just replaced the [timing belt](/topics-timing-belt-toyota/) the timing belt as I thought that was the culprit but I’ve come to find that it wasn’t and my car still has a loud rattle

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com