Ford Courier Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(24)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(24)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Ford Courier Brake Drum Replacement is $455 with $237 for parts and $218 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1978 Ford CourierL4-2.3LService typeBrake Drum ReplacementEstimate$784.45Shop/Dealer Price$929.95 - $1305.69
1977 Ford CourierL4-2.3LService typeBrake Drum ReplacementEstimate$730.45Shop/Dealer Price$876.00 - $1251.77
1977 Ford CourierL4-1.8LService typeBrake Drum ReplacementEstimate$793.69Shop/Dealer Price$955.05 - $1378.25
1978 Ford CourierL4-1.8LService typeBrake Drum ReplacementEstimate$793.69Shop/Dealer Price$954.99 - $1378.14
1976 Ford CourierL4-1.8LService typeBrake Drum ReplacementEstimate$793.69Shop/Dealer Price$955.09 - $1378.32
1982 Ford CourierL4-2.3LService typeBrake Drum ReplacementEstimate$692.46Shop/Dealer Price$833.99 - $1206.76
1975 Ford CourierL4-1.8LService typeBrake Drum ReplacementEstimate$807.19Shop/Dealer Price$968.18 - $1391.10
1981 Ford CourierL4-2.0LService typeBrake Drum ReplacementEstimate$844.75Shop/Dealer Price$1016.13 - $1467.99
Show example Ford Courier Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Ford mechanics

Real customer reviews from Ford owners like you.

Excellent Rating

(24)

Rating Summary
24
0
0
0
0
24
0
0
0
0

Rigoberto

11 years of experience
739 reviews
Rigoberto
11 years of experience
Ford Focus L4-2.0L - Brake Drum - Evanston, Illinois
Very knowledgeable and friendly. He explains exactly what he does, while doing the job. Learned a lot from him.

Isai

27 years of experience
230 reviews
Isai
27 years of experience
Ford F-150 V8-5.4L - Brake Drum - San Antonio, Texas
Fast, Friendly, Honest, Convenient! Thanks so much!

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
Ford Contour V6-2.5L - Brake Drum - Peoria, Arizona
Peter proved to be the problem solver with my cars repair, I cannot thank him enough, my car drives like it did when I first bought it, 20 yrs ago. I am so happy !!! J.A.

Patrick

15 years of experience
406 reviews
Patrick
15 years of experience
Ford Escape V6-3.0L - Brake Drum - Santa Ana, California
Patrick was awesome, He arrived at the scheduled time and completed the work in a timely fashion. He also corrected a problem another mechanic had done on my brakes for no charge.

Excellent Rating

(24)

Rating Summary
24
0
0
0
0
24
0
0
0
0
Number of Ford Brake Drum Replacement services completed
264+
services done by our mechanics
TOTAL NUMBER OF EXPERT Ford MECHANICS
1700+
experts on our platform

Recent articles & questions

Insurance Requirements for Car Registration in Indiana
In In order to drive a vehicle legally in the state of Indiana, you are required to renew your vehicle registration every year at the Bureau of Motor Vehicles. In order to do so, you must provide proof that you...
Missouri Speed Limits, Laws, and Fines
Following Following is an overview of the laws, limits, and fines as they relate to speeding traffic violations in the state of Missouri. Speed limits in Missouri 70 mph: rural freeways and interstates 65 mph: rural expressways 60 mph: urban...
Disabled Driver Laws and Permits in Virginia
In In the State of Virginia, if you are disabled, then you can obtain special license plates or placards from the Virginia DMV that will allow you to park in special places, and also benefit from other privileges accorded to...

Getting fumes and smell while idling and driving

Hello there, many common faults will cause your 2003 Audi A4 to have fumes and a smell when idling. Generally any EVAP or gasoline vapor leaks will trigger a check engine light with an EVAP leak code. In some cases...

I have a 2001 Saab 93 turbo automatic and it keeps stalling. Once it does, I have to wait about 20-30 mins to restart.

Hi there. Check the spark plugs (https://www.yourmechanic.com/services/spark-plugs-replacement) and see if they have been replaced. The plugs in your engine are designed to last between 80,000 to 100,000 miles. Replace the spark plugs if they have not been changed. If the...

I have a stutter when I am driving

The stutter, or vibration, could be due to an engine management (tuning) issue or is possibly caused by worn motor mounts that are allowing engine vibration to transfer to the body when the engine is under load. To evaluate the...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com