Dodge W300 Pickup Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(13)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(13)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a Dodge W300 Pickup Brake Drum Replacement is $453 with $225 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1971 Dodge W300 PickupV8-5.2LService typeBrake Drum ReplacementEstimate$726.44Shop/Dealer Price$863.05 - $1218.90
1972 Dodge W300 PickupV8-5.9LService typeBrake Drum ReplacementEstimate$794.32Shop/Dealer Price$959.95 - $1402.74
1974 Dodge W300 PickupV8-5.2LService typeBrake Drum ReplacementEstimate$794.32Shop/Dealer Price$959.94 - $1402.73
1974 Dodge W300 PickupV8-7.2LService typeBrake Drum ReplacementEstimate$794.32Shop/Dealer Price$959.89 - $1402.64
1971 Dodge W300 PickupV8-6.6LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.13 - $1171.04
1969 Dodge W300 PickupV8-6.3LService typeBrake Drum ReplacementEstimate$678.44Shop/Dealer Price$815.09 - $1170.97
1968 Dodge W300 PickupV8-6.3LService typeBrake Drum ReplacementEstimate$690.44Shop/Dealer Price$826.77 - $1182.40
1969 Dodge W300 PickupL6-3.7LService typeBrake Drum ReplacementEstimate$690.44Shop/Dealer Price$827.66 - $1183.96
Show example Dodge W300 Pickup Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Dodge mechanics

Real customer reviews from Dodge owners like you.

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0

Raymond

37 years of experience
412 reviews
Raymond
37 years of experience
Dodge Dakota V6-3.9L - Brake Drum - Las Vegas, Nevada
Great mechanic great work.

Grzegorz

41 years of experience
473 reviews
Grzegorz
41 years of experience
Dodge Caliber L4-2.0L - Brake Drum - South San Francisco, California

Christopher

27 years of experience
348 reviews
Christopher
27 years of experience
Dodge Caliber L4-2.0L - Brake Drum - Lakeland, Florida
Had another great experience w/ Christopher today. He's an A+ Mechanic who's gone above and beyond to fix my vehicle and answer all of my questions.

Scott

36 years of experience
902 reviews
Scott
36 years of experience
Dodge Caliber L4-2.0L - Brake Drum - Chandler, Arizona
Good guy. Fast. No problems

Excellent Rating

(13)

Rating Summary
13
0
0
0
0
13
0
0
0
0
Number of Dodge Brake Drum Replacement services completed
143+
services done by our mechanics
TOTAL NUMBER OF EXPERT Dodge MECHANICS
1400+
experts on our platform

Recent articles & questions

How Long Do Spring Insulators Last?
Most Most cars use a shock/strut suspension system with coiled springs to provide comfort and improve handling on the road. It’s reliable, lasts a relatively long time, and performs pretty well. It also doesn’t have some of the problems found...
How to Register a Car in Georgia
All All vehicles must be registered through Georgia’s Motor Vehicle Division (MVD). If you have just moved to the state, you have 30 days from the time you become a resident to make sure your vehicle is registered. Before registering...
P0028 OBD-II Trouble Code: Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)
P0028 P0028 trouble code definition Intake Valve Control Solenoid Circuit Range/Performance (Bank 2) What the P0028 code means P0028 is the OBD-II generic code indicating the engine control module (ECM) has determined that the variable valve lift for the intake...

Every 500 miles, 'check engine' light comes on and oil has to be added

Hello. It is common for this engine to consume oil as it ages (https://www.yourmechanic.com/article/What-Does-It-Mean-When-My-Car-Is-Burning-Oil_3). Typically the oil consumption comes from the valve stem seals. The only way to repair it is with rebuilding the cylinder head. I usually will look...

2002 Infinity I35 oil leak/white smoke under hood

Valve cover gaskets (https://www.yourmechanic.com/services/valve-cover-gasket-replacement) are a common source of oil leaks. However since your engine has oil all over the block, it 's best to clean the engine of all the built up oil so the source of the leak...

Leaking coolant and coolant jug has to be filled every other day

There are more than five different coolant hoses on your Mitsubishi Montero that may be causing the coolant leak. Without being there to physically inspect the vehicle, it's hard to diagnose precisely which one is causing the leak (https://www.yourmechanic.com/article/how-to-find-the-source-of-an-oil-leak-by-ed-ruelas). The...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com