Chevrolet Uplander Car Battery Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(5)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(5)

Car Battery Replacement Service

How much does a Car Battery Replacement cost?

On average, the cost for a Chevrolet Uplander Car Battery Replacement is $296 with $156 for parts and $140 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2006 Chevrolet UplanderV6-3.5LService typeCar Battery ReplacementEstimate$466.56Shop/Dealer Price$548.05 - $784.42
2005 Chevrolet UplanderV6-3.5LService typeCar Battery ReplacementEstimate$457.55Shop/Dealer Price$537.27 - $772.32
2007 Chevrolet UplanderV6-3.9LService typeCar Battery ReplacementEstimate$457.55Shop/Dealer Price$537.30 - $772.36
2006 Chevrolet UplanderV6-3.9LService typeCar Battery ReplacementEstimate$457.55Shop/Dealer Price$537.30 - $772.36
2008 Chevrolet UplanderV6-3.9LService typeCar Battery ReplacementEstimate$457.55Shop/Dealer Price$538.77 - $774.94
2009 Chevrolet UplanderV6-3.9LService typeCar Battery ReplacementEstimate$545.73Shop/Dealer Price$647.66 - $948.97
Show example Chevrolet Uplander Car Battery Replacement prices

What are car batteries and how do they work?

A car battery is an energy storage device that relies on a chemical reaction within the battery to produce electricity. The stored electrical energy is used to initially operate the starter motor, ignition system, and fuel system on your vehicle. Once your car engine is running, the alternator supplies the electricity needed for all vehicle systems and charges the battery to replace the electric energy used when starting a car.

Most electric vehicles have a traction battery which is in addition to the standard 12 volt battery that is used to start the car engine. Traction batteries also convert chemical energy to supply electrical energy but operate at higher voltages and often are monitored by the PCM (Powertrain Control Module).

Battery

When to replace a car battery?

  • Your car doesn’t start. A new battery has a specified capacity to provide power. This capacity is referred to as the cranking amps rating of the battery. As a battery ages, the actual amps that a battery can supply becomes lower than its original rating Once the cranking amps fall below a critical threshold, it will be difficult or impossible to start your car.
  • Battery or charging system warning light is illuminated. Should a battery or charging system warning light illuminate, a mechanic should perform a few basic tests to determine if a battery replacement is needed.
  • Electrical components don’t work. Once a battery has started to fail, and the voltage produced by the battery drops, then vehicle electrical components can malfunction, such as the security system. If you are experiencing electrical malfunctions, it’s a smart idea to have the battery tested.

How do mechanics replace the battery?

  • A temporary power source might be installed to avoid the possibility of losing radio presets or stored data in the PCM while the battery is out. When the battery is already completely dead, this step is unnecessary.
  • The vehicle’s negative cable is removed from the battery, followed by the positive cable. The battery tie down system is loosened and the old battery removed.
  • Cable ends and wiring are carefully inspected to ensure cleanliness and no corrosion. In some cases, corrosion can be extreme and the cable may need to be replaced or wiring repaired.
  • The new battery is installed and the tie down system is reinstalled. Anti-corrosion compound is applied to the battery terminals. The positive terminal is reconnected followed by the negative terminal.
  • Some vehicles, for example some models of BMW, VW, and Audi, may require PCM programming to input battery parameters. This step, performed using a specialized scan tool, is necessary to maximize battery life and prevent electrical system malfunctions.
  • The car is started and charging system output is measured and compared against the factory OEM specification to ensure that the new battery will properly recharge. Generally, charging output will be in the range of 13.8 to 14.8 volts but the exact specifications vary by make and model.

Is it safe to drive with a battery problem?

Yes, but if you have a weak battery you might be left stranded somewhere if the battery dies completely and you cannot start your car. A faulty battery may also needlessly overload the alternator and could adversely affect the operation of the vehicle’s electrical system, including the vehicle security system and the shift interlock.

When replacing the battery keep in mind:

  • The quality of the electrical connections to the battery posts is important. Connections must be clean, free of corrosion and properly tightened.
  • Batteries store a large amount of energy and if short-circuited a battery could explode and can create intense discharges that can damage your eyesight. Insulated tools should be used to attach cabling to battery terminals. Otherwise, the battery’s positive cable can be shorted to ground or the positive and negative posts can be directly shorted. Batteries can only be safely installed from a positive terminal to positive wiring and from a negative terminal to body ground. If the polarity is reversed damage will likely occur to the vehicle’s electrical system.
  • Generally, a car battery will have a service life of 4 to 7 years. If a load test on a battery reveals a significant reduction in the capacity of the battery to provide power, you should buy a new battery rather than wait for the old battery to fail completely.
  • Batteries should only be disconnected if the engine is off and the alternator is not running. Disconnecting a car battery while the alternator is running can cause a voltage spike that will damage sensitive electronic components in the vehicle, such as the PCM.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert Chevrolet mechanics

Real customer reviews from Chevrolet owners like you.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0

Robert

17 years of experience
269 reviews
Robert
17 years of experience
Uplander 2008 - Battery - Spring, TX
Robert, contacted me and advised he was on the way. He arrived shortly thereafter. He was very Friendly and Professional. He repaired my vehicle and also did a courtesy inspection. Thank you.

Scott

30 years of experience
531 reviews
Scott
30 years of experience
Uplander 2007 - Brake pedal is spongy - Denver, CO
Scott was professional, friendly, timely and thorough. I have decided to use Scott for my other repairs, based on the performance of this job.

John

0 years of experience
155 reviews
John
0 years of experience
Uplander 2008 - Intake Manifold Runner Control - Cedar Park, TX
John was great. He showed me the part he replaced, explained how it worked and why it failed. Very personable, knowledgeable, and I didn't get that icky, "I'm a snow job" feeling a lot of women do dealing with mechanics. I will totally use John again for any routine maintenance and repairs.

John

0 years of experience
155 reviews
John
0 years of experience
Uplander 2008 - Serpentine/Drive Belt - Cedar Park, TX
John was great. He showed me the part he replaced, explained how it worked and why it failed. Very personable, knowledgeable, and I didn't get that icky, "I'm a snow job" feeling a lot of women do dealing with mechanics. I will totally use John again for any routine maintenance and repairs.

Excellent Rating

(5)

Rating Summary
5
0
0
0
0
5
0
0
0
0
Number of Chevrolet Uplander Car Battery Replacement services completed
55+
services done by our mechanics
TOTAL NUMBER OF EXPERT Chevrolet MECHANICS
1700+
experts on our platform

Recent articles & questions

P0317 OBD-II Trouble Code: Rough Road Hardware Not Present
P0317 P0317 code definition The P0317 code means that the PCM has indicated that rough road hardware is not present. What the P0317 code means When the P0317 code is present, the powertrain control module has found a variation in...
B1966 OBD-II Trouble Code: AC Post Heater Sensor Circuit Failure
B1966 means the AC heater sensor is not working properly, most likely due to a damaged electrical component.
How to Prepare for the Texas Driver’s Written Test
You You can’t wait to get behind the wheel and out on the open road, but you still have to jump a few hurdles before you can get there. Namely, you need to pass your Texas driver’s written test so...

Car powers down & says service traction & ESC Light

Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning LightThe Electronic Stability Control (ESC) system or the Traction Control System (TCS) indicator/warning light comes on briefly when the engine is started. If the system is working normally the indicator light goes...

knock sensor

Hello. To understand what is going on, lets discuss these two components and how they work. Harmonic balancers are essentially vibration dampeners in the engine that counteract the torque caused vibrations coming from the crankshaft. Every time the combustion cycle...

My service engine soon light is on. I hear like a rattling noise when engine is running sometimes. The power doesn't feel the same

If you are referring to the check engine light (https://www.yourmechanic.com/article/what-does-the-check-engine-warning-light-mean-by-spencer-cates) on your vehicle occasionally the cause of it illuminating is the gas cap is loose. If the rubber seal on the gas cap is intact and the cap is tight,...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (844) 997-3624 · hi@yourmechanic.com