BMW 1802 Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6,607)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6,607)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 1802 Brake Drum Replacement is $541 with $313 for parts and $228 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
1971 BMW 1802L4-1.8LService typeBrake Drum ReplacementEstimate$902.52Shop/Dealer Price$1101.16 - $1602.57
Show example BMW 1802 Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6,607)

Rating Summary
6,159
203
60
44
141
6,159
203
60
44
141

Theodore

16 years of experience
1592 reviews
Theodore
16 years of experience
BMW X5 V8-4.8L - Alternator - Redmond, Washington
Theodore was knowledgeable, polite and professional! I am very happy with my service and will use the him again for service on all my vehicles.

Theodore

16 years of experience
1592 reviews
Theodore
16 years of experience
BMW 535xi L6-3.0L Turbo - Coolant Recovery Reservoir - Everett, Washington
Great job thanks again!

Peter

43 years of experience
1321 reviews
Peter
43 years of experience
BMW Z4 L6-3.0L - Brakes, Steering and Suspension Inspection - Phoenix, Arizona
Pete was great! He arrived early and took plenty of time to evaluate and explain everything. I would definitely request his services again and recommend him. He's very professional and knowledgeable.

Jacob

15 years of experience
74 reviews
Jacob
15 years of experience
BMW 750Li V8-4.8L - Coolant is leaking - Lawrenceville, Georgia
Very knowledgeable, prompt and honest !

Excellent Rating

(6,607)

Rating Summary
6,159
203
60
44
141
6,159
203
60
44
141
Number of BMW services completed
72677+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

P0430 OBD-II Trouble Code: Catalyst System Efficiency Below Threshold (Bank 2)
P0430 code definition P0430 is a generic diagnostic trouble code that indicates a malfunction within the catalyst system. It may...
Child Seat Safety Laws in Massachusetts
In In the state of Massachusetts, there are regulations governing the ways in which children are restrained in motor vehicles. This state actually is far less specific than others when it comes to child seat laws, but the laws are...
Industry News for Automotive Techs: October 15-21
This week: home-brewed autonomous car, sneak peek at future Jeeps, scheming car hackers, Ram's off-road TRX concept, new turbo test kit from Lisle.

Calipers keep locking up even after replacing.

You need to have the brake master cylinder checked to see if the brake booster actuator pin is not adjusted correct and causing the brake master cylinder to hold partial pressure to the calipers. The caliper slides should also be...

1.Van shakes only when backing up. 2. While driving, van will not change gears.

Hi Arthur. Thanks for contacting us today. One thing that could cause both of these issues is a blown or leaking inner transmission seal. Since the automatic transmission works as a hydraulic unit, any leaks can cause inconsistent operation of...

2006 Chrysler 300 won't start but dashboards light up , there's sound. Car won't turnover or crank at all . Please help

Although the battery is new, it still should be load tested (https://www.yourmechanic.com/services/battery-is-dead-inspection) to ensure that the issue is not a faulty battery. Starter motors require a lot of current and just because the lights work, that doesn't mean the battery...

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com