BMW 330i GT xDrive Brake Drum Replacement at your home or office.

Our mobile mechanics offer services 7 days a week. Upfront and transparent pricing.

Estimate price near me

Service Location

Customer Ratings

(6,729)

Included for free with this service

Online Booking

Mechanic comes to you

12-month / 12k-mile warranty

Free 50 point safety inspection

Our certified mobile mechanics can come to your home or office 7 days a week between 7 AM and 9 PM.

Customer Ratings

(6,729)

Brake Drum Replacement Service

How much does a Brake Drum Replacement cost?

On average, the cost for a BMW 330i GT xDrive Brake Drum Replacement is $621 with $478 for parts and $142 for labor. Prices may vary depending on your location.

CarServiceEstimateShop/Dealer Price
2017 BMW 330i GT xDriveL4-2.0L TurboService typeBrake Drum ReplacementEstimate$1143.77Shop/Dealer Price$1401.59 - $2141.30
2018 BMW 330i GT xDriveL4-2.0L TurboService typeBrake Drum ReplacementEstimate$1118.40Shop/Dealer Price$1374.67 - $2105.13
2019 BMW 330i GT xDriveL4-2.0L TurboService typeBrake Drum ReplacementEstimate$1118.40Shop/Dealer Price$1374.66 - $2105.13
Show example BMW 330i GT xDrive Brake Drum Replacement prices

What are brake drums and how do they work?

A brake drum is a heavy, cast iron brake system part that looks like a shallow, several inches-high cylinder about 9 to 12 inches in diameter. The brake drum has a precisely machined surface all around the interior circumference, that the brake shoes make contact with when you apply the brakes, transmitting hydraulic pressure through the wheel cylinder. This forces the brake shoes outward against the interior of the brake drum, resulting in the friction that causes the car to slow. The brake drum is mounted over, and fully encloses, all of the rear brake components such as the wheel cylinder, springs and clips, brake shoes, and parking brake mechanism. The drum is commonly held to the wheel hub by the wheel and the lug nuts, but some configurations combine the drum with the wheel hub as one unit. Nowadays, a drum brake type system is only installed on the rear axle, if used at all, as 4 wheel disc type systems have become more common.

When to consider replacing brake drums:

  • Reduced braking effectiveness. If the brake drum is unevenly worn, scored or cracked, it will increase stopping distances. A cracked drum must be replaced outright but a worn drum can be restored on a brake lathe so long as enough metal material remains.
  • Pulsating brakes, pulling to one side, vibration or noise. If a brake drum is warped, is unevenly worn, or perhaps the brake shoes have worn down completely — creating metal-to-metal contact — you might detect pedal pulsation, the vehicle may pull to one side, or you might feel a vibration or hear a noise when you apply the brakes. The brake system will have to be inspected to pinpoint the exact problem.
  • Brake shoe replacement. Anytime the brake shoes are replaced, the drum must either be resurfaced or replaced outright. Installing new brake shoes on a used, unresurfaced drum will lead to poor results.
  • Loss of parking brake function. The parking brake locks the brake shoes against the brake drum. If the brake drum is cracked, the parking brake lever will pull up excessively and the car may still be able to roll. However, a more common circumstance is parking brake maladjustment or seizure of parking brake components. Repair of those problems will often require removal of the brake drum.

How do mechanics replace brake drums?

There are two options when it comes to brake drum service: outright replacement or resurfacing. In some cases, it is cheaper to replace the drum rather than refurbish it. In both cases though, the removal and installation procedure for the drum is the same.

  • Raise the vehicle and safely support it using steel jack stands.
  • Remove tire and wheel assembly.
  • Remove brake drum. Sometimes the brake drum has rusted to the wheel hub and removal of the drum will require a brake drum puller. In some cases, the wheel hub is integral to the brake drum, in which case the hub-bearing retaining bolt and the wheel bearing must be removed to replace the drum.
  • Measure the interior diameter of the machined surface in the drum with a brake drum micrometer or similar measuring tool. If sufficient metal exists to resurface the drum on a brake lathe, the mechanic will compare the cost of such restoration to the alternative: buying a new drum.
  • Prior to installing the resurfaced or new drum, the brake shoes, springs, wheel cylinder, parking brake mechanism, and backing plate are all inspected. All worn parts should be replaced. Generally, if drums have been replaced or resurfaced, new brake shoes should be installed. The worn shoes will cause irregular wear in the brake drum and reduce braking effectiveness.
  • The shoes are adjusted and the drum is installed. The wheel and tire assembly are installed and torqued in the proper sequence and the car is road tested to check the operation of the brakes.

Is it safe to drive with a brake drum problem?

No. Should there be a deficiency with the brake drums, stopping distances will not be as short as possible. In a panic stop, stopping just five or ten feet shorter could be the difference between no collision and a collision. Any deficiency in a vehicle’s braking system is a cause for concern and a potential safety issue. Have the brake drums inspected at your earliest convenience to determine if a problem exists and find out what must be done to fix it.

When replacing brake drums keep in mind:

  • With few exceptions, brake work on one end of an axle should be performed on both ends of the axle. Should a brake drum on one end of a front or rear axle be serviced, or brake shoes on one end are serviced, both sides of the axle should receive the same service. This helps to avoid problems, such as pulling, vibration, and so forth, once the vehicle is returned for use.
  • Brake drum systems use very powerful springs to keep the brake shoes in position. These springs are exposed to extreme heat. It is best practice to replace all springs whenever new shoes are installed. Should a spring unexpectedly break in the brake drum assembly, a mispositioned brake shoe could cause the brakes to grab and lock, which would pose a safety issue.
  • If the wheel hub and bearing are integral to the brake drum on your car, the mechanic may recommend replacement of the grease in the wheel bearings and inspection of the wheel bearings.
  • Since the arc of the brake shoes will not perfectly match with the arc of the drum when new, expect a bed-in period before maximum braking efficiency is achieved.

Fast and easy service at your home or office

Backed by 12-month, 12.000-mile guarantee


Meet some of our expert BMW mechanics

Real customer reviews from BMW owners like you.

Excellent Rating

(6,729)

Rating Summary
6,273
206
60
45
145
6,273
206
60
45
145

Jonathan

13 years of experience
171 reviews
Jonathan
13 years of experience
BMW 530xi L6-3.0L - Oil Change - Johnston, Rhode Island
Very Knowable and helpful

Jeff

19 years of experience
9 reviews
Jeff
19 years of experience
BMW 328i L6-3.0L - Serpentine/Drive Belt Replacement - Carlsbad, California
excellent customer service

Damian

11 years of experience
430 reviews
Damian
11 years of experience
BMW 328i L6-3.0L - Radiator - Clermont, Florida
Awsome job changing the radiator and all the hoses on my bimmer.

Raymond

27 years of experience
243 reviews
Raymond
27 years of experience
BMW 545i V8-4.4L - Alternator - Victorville, California
Very trustworthy & reliable mechanic , he directly tells you what the issue is & possibly what causes the issue. This is my second time having Raymond repair one of my vehicles , when I need to get some auto work done he’s the one I get ahold of ✅

Excellent Rating

(6,729)

Rating Summary
6,273
206
60
45
145
6,273
206
60
45
145
Number of BMW services completed
74019+
services done by our mechanics
TOTAL NUMBER OF EXPERT BMW MECHANICS
1100+
experts on our platform

Recent articles & questions

P0776 OBD-II Trouble Code: Pressure Control Solenoid B Performance
P0776 code means there is an abnormality within either the electronic pressure control circuit or solenoid often due too dirty fluids or faulty parts.
How to Replace an Exhaust Gas Recirculation (EGR) Valve
The exhaust gas recirculation (EGR) valve can cause drivability problems if it fails and should be replaced to avoid engine performance issues.
Nitrogen Vs. Air in your Tires
There are benefits to using air or nitrogen for tire inflation depending on your day-to-day driving conditions.

How do I open the instrument panel storage?

The instrument panel storage is located on top of your instrument panel, and offers extra storage space. At the front of the instrument panel storage is a handle: pull upwards on this handle to open the storage compartment. When you’re...

My car is overheating and my heater is blowing cold air on and off

The heater not working in some cases may be related to the overheating problem you are also having. This may be due to a faulty heater blower motor or potentially a bad heater core (https://www.yourmechanic.com/services/heater-is-not-working-inspection). As you may know, the...

I did something really stupid. I took one of my spark plugs out to check if it was wet after I replaced cooling fan switch and check [engine](/topics-engine/) light came on. I bled cooling system and rechecked coolant level also. But in the process I accidentally started my car with the plug out and now it won't start at all. It turns over but won't start. I'M A GIRL so don't be too hard on me My car has 142000 miles. My car has an automatic transmission This is exactly what hapoened to my bmw x5

How can we help?

Our service team is available 7 days a week, Monday - Friday from 6 AM to 5 PM PST, Saturday - Sunday 7 AM - 4 PM PST.

1 (855) 347-2779 · hi@yourmechanic.com