Q: Timing belt broke

asked by on October 14, 2016

My timing belt went in my car while i was driving aprox 30-35 mph. There was no noise or jump/ movement when it went. My car just stopped running and i immediately pulled over to a stop. I am just wondering aprox what the chances are that it may have bent or ruined valves & pistons? Theres no other visible damage to any other part of engine. The belt had barely moved when it went.

My car has 90000 miles.
My car has an automatic transmission.

Serpentine/Drive Belt Replacement $111.60 - $349.96 Get a Quote

I believe that you are right: your drive belt is broken. Unfortunately, this happens to everyone at some point. The best course of action is just to replace the belt. I don’t believe anything happened to any internal engine parts or other parts of your car, but it is a good idea to have a professional technician, such as one from YourMechanic’s service team, replace your serpentine belt and check for any possible damage.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

How do I adjust the position of the steering wheel?
The steering wheel in the vehicle is able to move up and down to accommodate drivers of different heights and driving preferences. This not only improves driver comfort, it also positions the airbag to be in front of the driver...
Where and how should children be seated?
While adults can sit in any position in your car, that’s not true for children. Children must be properly seated at all times, but the type of seating will vary depending on your child’s age, weight and more. Here’s a...
Car going into Limp Mode
Your problem may be something simple or more complex. The first thing that needs to happen is for the Diagnostic Trouble Codes or DTC's to be read and addressed. There are only a few things that can put your car...
Car making a spark sound when starting
While the information provided is a bit limited, it does lead me to believe that your Nissan may be experiencing an electrical problem with the starting system. Since I am unable to give a proper diagnosis, I highly recommend enlisting...
Advice on buying a 4-wheel drive vehicle with minor and major repairs
Minor are the stuff like brakes, water pump leaking, radiator caps with holes in them - stuff that doesn't cost that much to fix and what you can easily do by yourself. But, if the transmission or the engine have...
P2402
Hello and thanks for your question. The code P2402 (https://www.yourmechanic.com/article/p2402-obd-ii-trouble-code-evap-leak-detection-pump-control-circuit-high-by-jay-safford) is usually caused by EVAP control system pump current goes higher than specified. The evaporative system pump could be drawing too many amps or the pump motor has a short...
How do you replace a thermostat on a 2006 mercury mariner
Hello. Thank you for writing in. The basic procedure for replacing the thermostat is pretty simple. You start by accessing the thermostat. Remove the hoses and retaining screws, and then removing the housing. Replace the thermostat outside and inspect the...
CV Joint Change instead of the wheel hub assembly.
Customer wants to change the information from having a wheel hub assembly replacement changed to a CV Joint / CV Shaft replaced on the set up page.

Related articles

How Belt Pulleys Work
There There are two main types of car pulleys: crank pulleys, and accessory pulleys. Most pulleys are driven by a main crank pulley, which is bolted onto the crankshaft. When the engine is operating, the crank pulley rotates, transferring motion...
Suzuki Certified Pre-Owned (CPO) Car Program
If If you have been shopping for a used Suzuki vehicle, you may want to check out cars under their certified pre-owned program. Many manufacturers have a certified pre-owned (CPO) program, and each one is set up differently. Read on...
How to Inspect Valve Clearance Adjustment
The The term “valve adjustment” is an oxymoron. What is actually being adjusted is the clearance between the linkage of the camshaft and the valve (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-valve-cover-gasket). It is most often called the valve lash. This system that links the camshaft...