Q: The Crankshaft Position Sensor broke at the block - how do i get it out? 1998 Chrysler Cirrus
The CPS broke at the block as I was removing it. It has about 11/2 inch left out of the block but I cant get anything in there to grip it.
My car has 186000 miles.
My car has an automatic transmission.
Recommended Services
| Crankshaft Position Sensor Replacement | $120.83 - $900.50 | Get a Quote |
Hello - I would soak it with penetrating oil (WD-40, PB Blaster, etc.) overnight, then try drilling the sensor for a screw/bolt extractor. If that fails, you may have to keep drilling with larger and larger bit sizes until, you can deform the thin metal liner of the sensor enough to get hold of it and pull it out. For assistance, I recommend a crankshaft position sensor replacement performed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, solve this problem, and install a new sensor for you.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
Getting poor fuel mileage lower than listed
Fuel economy has many influences on it which can raise or lower the MPG. Are you calculating fuel economy per tank or off the trip computer? The trip computer is a constant average that might be resettable (see owner manual)....
Recently purchased a 2013 Chevrolet Silverado z71 5.3L engine and truck has a rough idle and hesitation on accelerating.
Hello. Most of the time this is caused by an issue with the variable valve timing. Since you do not know the history of the engine it may have some sludge built up inside which is going to affect the...
can i remove cylinder head without removing engine from the car
It is possible to remove the head (https://www.yourmechanic.com/article/how-to-replace-a-head-gasket-by-jerel-lawrence) while the engine is in the car, but it's going to be tight. This can be a difficult and even dangerous job. Unless you feel very comfortable with this type of work,...
Car stopped while driving and won't start even with a jump.
Hello, thank you for writing in. The starter would not prevent the vehicle from driving. Once it is used to turn over the engine when starting, it is useless to the vehicle. It is more likely a battery or alternator...
loud squeaking noise when i start car in cod weather and when i turn corners it does go away.
Typically, a loud squeal on a cold start could be belt related. As belts age, the rubber becomes harder and glazes a bit. This can cause a brief, or constant, squealing. Also, belt tension can cause squealing as well. If...
Horn doesn't work when I push on the steering wheel but when locking car it does what would cause this problem?
Hi there - your symptoms describe a failure of the horn switch (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-horn-switch_2) itself. The fact that the horn works when the security system is armed (when locking the vehicle) indicate that the horn and the wiring to it work...
My Boat motor repair issue
Hi there. Unfortunately, we do not provide services or repair advice for off-road vehicles or mechanical components. You might be better served to contact a powersports or off-shore mechanical repair shop.
Why is my truck is leaking transmission fluid?
Hi there. Check the location of the transmission fluid leak on the case to determine what needs replaced. There are 5 locations for the transmission to leak that are common. Locations of a leak The input shaft seal The rubber...
Whine from 2011 f150 drivetrain
Hi there. If the replacement transmission you installed was used, it's quite possible that some component inside is damaged as well. However, it is more likely that the initial diagnosis is incorrect if you are still hearing this pining sound....
Related articles
Is It Unsafe to Continue Driving a Vehicle with Broken Wheel Speed Sensors?
Car wheel speed sensors are an important safety feature. It helps the ABS system work when you need to make an emergency stop.
A Buyer’s Guide to the 2012 Chrysler 200
In In 2011, Chrysler completely overhauled, updated, and remodeled their entire line, including the introduction of the new Chrysler 200. This reimagining of the old, boring Dodge Sebring sedan was already an exciting move for Chrysler, and the 2012 Chrysler...
How to Replace an Intake Air Temperature Sensor
An air temperature sensor, or air charge temperature sensor, signals a car’s computer about the air-to-fuel ratio. Replacing one requires few tools.
Browse other content
Maintenance
Cities
Services