Q: Smoke from engine cooling fan

asked by on April 22, 2017

When I was getting back home, I smelled a burning smell of plastic, I opened the hood and found smoke from the radiator cooling fan, I let the engine cool down and checked the coolant level it was in the max level , I started the engine and drove for 2 kms the engine was not heating up and the heat indicator was little below the middle (Approximately 90 degrees). The fan was not rotating I tried to move it, it was too hard to move, the other fan runs when I switch on the AC. Do I need to replace the faulty fan alone orcheck for any other components, it is advisable to drive the car with this fault ? The car is an Optra 1.6 Petrol 2006 Model.

My car has 50000 miles.
My car has a manual transmission.

Cooling/Radiator Fan Motor Replacement $135.68 - $1518.55 Get a Quote

It’s not unusual for a fan to fail, and you can probably get away with replacing just that. But since the fan seized, there may be a blown fuse or fusible link back in the system that will also have to be changed. If you are going to try to operate the car, you should unplug the electrical connector from the fan to prevent damage to the fan controller. If there are no other problems the car shouldn’t overheat as long as you are moving forward. If you want to delegate this job, you can contact Your Mechanic. They can send a technician to your home or office to replace your radiator fan right there on the spot.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

Clutch problems with my BMW.
We need to know if there is pressure on the clutch pedal or if it is loose. If the clutch pedal has no pressure, make sure there is brake fluid in the master cylinder. I would have a technician inspect...
Air not working after alternator repair
There is a chance that the electrical connector that goes to your AC compressor may have gotten disconnected while the alternator was being worked on; it is in close proximity to the alternator and may have been bumped. I would...
Driveshaft assembly
Hello, thanks for writing in. The driveshaft assembly is composed of the driveshaft, U-joints and snap rings. Both ends of the driveshaft connect to the output shaft and differential via yokes. If you would like help with this replacement, consider...
Brake exhaust doesn't shut off when I press on the accelerator.
Hello and thanks for your question. When you press the accelerator to deactivate the jake brake system, the electronic throttle sends a signal to the computer to shut off the power to the jake brakes for acceleration. The switch inside...
Have to accelerate slowly or dies
Hey there. This problem of stalls on acceleration (https://www.yourmechanic.com/services/car-shuts-off-when-stepping-on-gas-pedal-inspection) is most likely caused by the carburetor accelerator pump (https://www.yourmechanic.com/services/accelerator-pump-replacement) is not pumping fuel into the engine when the throttle is pressed. This explains the vehicle running great at steady speeds...
No rear lights of any kind or working. ( No running, brake, or signal lights)
Check the ground wires on the back of the vehicle as they are either broke or loose. Over time the bolt that holds the ground wire to the frame tends to become rusty causing the ground to have a high...
Showing signs of a blown head gasket.
If there is a head gasket leak, as the engine heats up and expands, that may be sealing the leak somewhat and that would explain your experience. Based on what you are describing, it certainly sounds like a break at...
After a fuel injector/throttle body cleaning, my Idle goes up and down constantly in park. When in gear it doesnt.
Hi DeShon. Thanks for contacting us today. Usually, when a mechanic cleans a throttle body and fuel injectors with a chemical additive, it's seafoam; which can be rather harsh on sensors and other fuel system components. This is often the...
Pulling codes...po206 and po306, cylinder 6 misfire. Changed fuel injectors, fuel injection connectors, spark plugs, ignition coil
Hi Brett. Thanks for contacting us today. Typically, when you've replaced the fuel injectors, plugs and wires, and still getting a single cylinder misfire, it's going to be related somehow to the ECU. Either a trouble code is stuck or...

Related articles

A Buyer’s Guide to the 2012 Chevrolet Silverado Hybrid
If If you’re looking for a half-ton pickup truck that also gets great gas mileage, look no further than the 2012 Chevrolet Silverado Hybrid. While it has the towing and carrying capacity you’d look for in any regular truck, it...
The Best Used Cars to Buy If You’re an Electrician
As As an electrician, you have to haul around wiring, tools and equipment, and tons of supplies. You can’t get by with a small used car, or even a big one. What you probably need is a good used cargo...
The 5 Safest Used Cars You Can Buy For Under $20,000
The Subaru Legacy, Honda Accord, Ford Fusion, Chevy Volt, and the Volvo XC60 are five of the overall safest used cars you can buy for under $20,000.