Q: Pressure Control Solenoid 'B' Control Circuit Range/Performance Read more: https://www.autocodes.com/p0965.html
can you guy's help me I am pressure on my gas pedal and it isn't going Pressure Control Solenoid 'B' Control Circuit Range/Performance
My car has 83000 miles.
My car has an automatic transmission.
Recommended Services
| Check Engine Light is on Inspection | $94.99 - $114.99 | Get a Quote |
Hello, thank you for writing in. The reason your are not getting a response from your gas pedal is due to the transmission fluid pressure is off, or the computer thinks it is. Typically this is caused by a bad solenoid used to regulate the pressure, or the connection to the solenoid is weak. A weak connection can be caused by the physical wires being loose or dirty, or from the solenoid being loose or dirty. Make sure everything is clean, dry, and tight before replacing the solenoid. For more help, contact our service department to schedule an appointment.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
Car shaking and stalling after adding oil.
Hello, running a car without oil can be catastrophic. It is possible that you have turned bearing or damaged the connecting rods or pistons. It sounds like you may have broke something there is no way of telling without taking...
Steering issues
It is possible that the play you are feeling in your steering wheel may be related to worn out wheel bearings (https://www.yourmechanic.com/article/symptoms-of-bad-or-failing-wheel-bearings). The wheel bearings may not be noticeable in the steering wheel when the vehicle is stopped or parked,...
run away idle/engine speed
This can be cause by a few things. A sticking throttle cable or throttle body (https://www.yourmechanic.com/services/clean-throttle-body), due to excess carbon buildup, or expansion from heating, idle air control valve issue, it can also be caused by a faulty temperature sensor...
Stalling engine, brakes, power steering and transmission failure
The stalling may well be caused by a failure of the crankshaft position sensor (https://www.yourmechanic.com/services/crankshaft-position-sensor-replacement). This device provides timing instructions for the ignition system. When it fails, the engine no longer gets spark at the spark plugs (https://www.yourmechanic.com/services/spark-plugs-replacement) and stalls....
How to replace brake caliper
If the brake caliper is sticking due to the piston binding in the caliper then it should be replaced. Raise and support the vehicle, remove the tire, and disconnect the brake line attached to the caliper. Remove the caliper attachment...
Knock sensor 1
Hello there. The knock sensor code (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-a-faulty-knock-sensor) can have various causes on your 2004 Chevrolet Silverado. The knock sensor circuit low, bank 1 code is telling us that the knock sensor in bank 1 that it has low circuit voltage....
i have a 1994 z28 and i did a head gasket replacement for some blown head gaskets. I then tried changing the timing gears and when
Hi there. It really depends on the location of the motor (meaning if it's installed in the vehicle or loose and on an engine stand), that would factor into the price and whether this is a project one of our...
Car intermittently won't start -- this time won't even start when jump started
Hi Eric M. An issue like you've described is very difficult to diagnose without an onsite inspection (https://www.yourmechanic.com/services/electric-problems-inspection). If you're able to activate the starter on a consistent basis, then you can rule that component out as the source of...
F150 running rich
The most common causes of too much fuel being delivered are: a dirty mass air flow sensor that overstates the amount of air entering the engine; a faulty oxygen sensor; a faulty coolant temperature sensor (the temperature signal is a...
Related articles
P0003 OBD-II Trouble Code: Fuel Volume Regulator Control Circuit Low
P0003 P0003 trouble code definition The P0003 code is associated with the electrical circuit which connects to your fuel pressure regulator. It also may be related to other codes, such as: P0001, P0002, or P0004. What the P0003 code means...
P2020 OBD-II Trouble Code: Intake Manifold Runner Pos Sensor/Switch Circuit Range/Performance Bank 2
P2020 P2020 Code Definition A P2020 code is a generic powertrain code related to the fuel and air metering and auxiliary emissions control systems. The Intake Manifold Runner Control (IMRC) controls are utilized to change or control airflow in the...
P0813 OBD-II Trouble Code: Reverse Output Circuit Malfunction
P0813 P0813 code definition P0813 is the fault code for the Reverse Output Circuit. What the P0813 code means This is the generic OBD-II fault code indicating an issue within the reverse output circuit. When you shift your vehicle into...
Browse other content
Estimates
Services
Maintenance