My car was accelerating on its own but has stopped doing ...
Responses
Nachum Wagschal
246 days ago
Good Morning
Have you had your spark plugs and wires replaced ?
I would check for check engine light codes and then probably do a tune up first .
Nachum Wagschal
246 days ago
You also want to check for vacuum leaks .
Let me know if you have any other questions
Customer
246 days ago
How do you scan for codes on a car with an OBD1 connector?
Nachum Wagschal
246 days ago
You can use a scanner that will check OBD 1
or you can flash the light for the codes see these instruction
[https://mechanicbase.com/trouble-code/obd1-codes/](https://mechanicbase.com/trouble-code/obd1-codes/)
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
What does the malfunction indicator Warning Light mean?
The malfunction indicator Warning Light is on your instrument cluster. It illuminates when the On-Board Diagnostics-Second Generation (OBD II) system detects an issue. The OBD II system monitors your vehicle’s emissions. When the malfunction indicator Warning Light is illuminated, it...
Leaking oil into the intake and PCV and catalytic converter
You would need to have the entire crankcase ventilation system checked and serviced first to make sure all the PCV valves are clean and working correctly, or if excessive oil will be consumed and get in the intake. The turbo...
My car has transmission problems - 1990 Toyota 4Runner
Hello there, many faults will cause shifting issues with your 1990 Toyota 4Runner. The most common faults are low transmission fluid, faulty shift linkage, clutch cable, slave cylinder, or clutch. If the 4 wheel drive linkage is faulty, it should...
Everything works but it won't crank
If the motor just stopped out of nowhere, this may suggest many different possibilities such as a loss of spark or a fuel delivery problem. If the motor does not crank, this may suggest an issue related to the starter...
safe jack points with floor jack
Many vehicles are safe to jack up on the axles, control arms, subframes, and sometimes the pinch weld. Be careful lifting on the pinch weld of some vehicles as it can cave in and cause seriouse body damage. If you...
My clutch is not working Entire clutch repair or clutch master cylinder repair? How do I check the cylinder?
Hi there. Check the slave cylinder to the clutch and see if the piston is all the way out. If the piston is all the way out or its not touching the clutch fork, then the release bearing has broken...
My speedometer, rpm gauge and fuel gauge are not working; possible gear slipping and high rpm.
Hi there. For the electrical issues on the dash that are not working properly, I recommend that you have your battery check and loaded. The battery could have 12.6 volts, but if a cell is burnt or damaged, the battery...
Transmission failsafe program
When you get the transmission fail safe warning, it means the transmission controller has detected a fault in the transmission or in the various sensors that it reads. The controller can adapt to a certain amount of wear and tear...
Car won't start
Without seeing the extent of the damages it would be hard to figure out the part that is damaged. I suspect the steering column ignition switch got damaged.
Browse other content
Estimates
Cities
Services
My car was accelerating on its own but has stopped doing that and now is stalling and has a rough idle Mechanic's Assistant: Is the rough idle intermittent or consistent? Hardly noticeable but I believe it’s constant. It ...
My car was accelerating on its own but has stopped doing that and now is stalling and has a rough idle Mechanic's Assistant: Is the rough idle intermittent or consistent? Hardly noticeable but I believe it’s constant. It just doesn’t feel right Mechanic's Assistant: What is the make/model/year of your car? Pontiac Bonneville SE 1994 Mechanic's Assistant: Are you fixing your Bonneville yourself? What have you tried so far? Ive replaced the air filter, which was filthy, but it seems like the idling got worse ironically Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? I accelerate get “check gauges” it stalls while driving, then “service engine soon” light. Starts up right away just to repeat that signaling process