Q: My 2007 Ford Fusion clicks, then will eventually start.

asked by on January 10, 2017

2007 Ford Fusion wI'll click 7 to 8 times before it starts. I'm assuming it's the starter solenoid or starter as a whole. A few months ago it would just click once every so often, then it would start. Now I have to turn the key 7 to 8 times before it will start. Battery is good... Any ideas?

My car has 170000 miles.
My car has an automatic transmission.

Hi There, It sounds like you are correct in that you have a failing starter solenoid. As you know, the starter solenoid is located on the starter and has internal electrical contacts that transmit electricity to the starter. As electricity is supplied to the starter a small gear comes out and engages the flywheel to spin the engine over as you turn the key. When this fails, it may cause a clicking sound and will not allow the starter to engage the flywheel when you turn the key as you have described. I would recommend having a professional from YourMechanic come to your location to diagnose and inspect your vehicle.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

Burning oil, can’t sustain the oil changes
Hi, You are not alone. Nissan has released a recall, ntb06-082, that deals with this issue and estimates that roughly 115,000 vehicles are affected. The fix for the oil consumption may be as serious as engine replacement, or as simple...
Low RPMs
Hi there. This is a common problem for your vehicle. There are many different things that can be effecting your idle rpm. The Idle Air Control Valve for your Vanos needs attention. Vanos is the variable valve timing BMW incorporated...
Put a new transfer case on, now tranny won't shift out of first unless I do it manually
Hi there, thanks for writing in about your 2000 GMC Sierra 1500. Your transmission and ABS system need a vehicle speed reference to operate correctly. The transfer case has two speed sensors (https://www.yourmechanic.com/services/speed-sensor-replacement) located at the rear extension housing. Inspect...
Body throttle wont accelerate when pedal is pressed, car starts at very low idle
It is possible that the idle speed is out of adjustment. Many vehicles from the 1980s have adjustable idle speeds to improve power or fuel economy. I would recommend having the idle speed adjusted (https://www.yourmechanic.com/services/engine-idle-speed-is-high-inspection) to the factory specifications by...
Car revs when turning the key
Hello - yes, you probably need a new throttle position sensor. The symptoms you describe are classic throttle position sensor failure symptoms. I would recommend having a Throttle Position Sensor Replacement Service (https://www.yourmechanic.com/services/throttle-position-sensor-replacement) completed by a mobile, professional mechanic, such...
What are the signsof a bad tensioner pulley?
The most common cause of noise in the front of the motor having to do with the accessories is the tensioner and idler pulley bearings get noisey. I have also seen where the a/c compressor pulley bearing gets noisey. You...
High rpms and no acceleration
This may be a result of low transmission fluid (https://www.yourmechanic.com/services/transmission-fluid-service) or potentially a faulty transmission control module. A faulty transmission control module may cause a delay in acceleration or erratic shifting of gears. The transmission control module has various sensors...
Steering column makes a clicking noise
Hello there. There are many possible reasons that the steering wheel may be making this sound. Your vehicle has an intermediate shaft that goes from the steering wheel to the rack and pinion assembly. This shaft has a u-joint on...
Can I use the product "Permatex 24125 Ceramic Extreme Brake Parts Lubricant" on semi-metallic brake pads? 2015 Mitsubishi Lancer
Hello. Yes, you can use this on the back side of the brake pads and on any other contact point in the brake pad bracket. This will assist in reducing noise.

Related articles

A Buyer’s Guide to the 2012 Ford F-450
The The 2012 Ford F-450 is a serious truck with major towing and hauling capacity. What it lacks in gas mileage, it more than makes up for in durability, suspension, power, and torque. Plus, with a six-speed shiftable automatic transmission,...
2012 Ford Mustang vs. 2012 Dodge Charger: Which One Should I Buy?
Technically these two vehicles have wildly different classifications: compact for the Ford Mustang and large car for the Dodge Charger. However, who would consider either one anything other than a muscle car? These cars are meant for speed, fun, and...
2012 Honda Civic vs. 2012 Ford Focus: Which One Should I Buy?
One of the best ways to cope with pain at the gas pump is to look at downsizing your vehicle, and today’s compact cars are a great option that allow you to keep the space that you need to move...