Q: My 2003 Saturn Vue is having clutch issues

asked by on November 08, 2016

I was driving along started going down a small hill to a stop sign so i put car in neutral. When i reached stop sign i Tried to put my vehicle in gear and it was hard to put in gear all the way up to 5th gear i struggled and felt that there was a difference in clutch and went about 3 or so miles came to a stop light and car would not go into gear at all... I checked the fluid had to add just a tiny tiny bit then i bled the line car ran less than a day and now i have complete loss of clutch

My car has 110000 miles.
My car has a manual transmission.

Clutch is not fully disengaging Inspection $94.99 - $114.99 Get a Quote

Hello - most likely your clutch hydraulic system has worn out. If fluid leaks on the ground under front driver side of the car (clear fluid, but oil film on the fingers), the clutch slave cylinder has worn out, or there is a leak in the fluid line. If there is fluid on the carpet of the driver side floor mat, the clutch master cylinder is worn out. Best to replace both at once if one or the other is worn out - they tend to wear out at a similar rate. I would recommend having a clutch is not fully disengaging inspection completed by a mobile, professional mechanic, such as one from YourMechanic, who will come to your location, diagnose this problem, give you an accurate assessment of damage and cost estimate for repairs.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

Replaced cam shaft P sensor. Less than 2 weeks. Now its bad again. What else could i replace before i buy another sensor?
First I would make sure you replaced the cam sensor on the driver's side of the engine. This is bank 2. Now you have a noise in the motor, and it is rattling and running rough. I would point you...
Humming/whirring sound only when accelerating.
It is possible that you have a wheel bearing issue (https://www.yourmechanic.com/services/wheel-bearings-replacement). It is usually worse when cornering in one direction and gets better when turning the other direction if it's just one bearing. The brake noise could be the return...
Does my vehicle have an oil pressure sender or oil pressure sensor or both and where is it located?
Your motor (454/7.4L Big Block Chevy) should have an oil pressure sending unit that is typically mounted just above the oil filter housing. This is a relatively small unit (about the diameter or a quarter or slightly bigger) with threads...
The car starts by itself!!!!
Hi there. In order for an engine to start, the ignition relay needs to send an electric signal to activate the fuel system, ignition system and eventually the starter to crank the motor. This happens in three possible ways. First,...
what does trans.failsafe prog mean
It means that the ECU (Electronic Control Unit) has detected a problem in the transmission itself or in one of the devices or sensors that controls it. The ECU then substitutes whatever information its not getting with a fixed value...
why is my car shaking & raddle & why is my check engine light still on after i added oil
Hello, and thank you for writing in. Typically shaking is a sign of misfiring. Misfiring occurs when the air, fuel, or spark are being sent to the engine improperly. Since the check engine light is on, there is a strong...
My 2004 Pontiac Montana won't start just clicks when I turn key but lights,radio still work & its a new battery. What could it be?
It sounds like you may have a weak battery, a failing voltage regulator or failing alternator. As you may know, the alternator charges the battery while the engine runs by generating amperage and recharging the battery while the engine turns...
2013 hyundai genesis 2.0 turbo how much to replace the chutch
Depending on what needs to be replaced the price to replace may vary. If the clutch pack is burnt, this may be one component of what needs and if it needs a throughout bearing, this may be an additional component...

Related articles

How to Buy a Good Quality Clutch Master Cylinder
The The master cylinder in a manual transmission system functions similarly to the brake master cylinder, and in fact, both systems use brake fluid to lubricate the interior components and provide the pressure necessary to operate the other elements of...
Symptoms of a Bad or Failing Clutch Master Cylinder
Common signs include low or dirty fluid, difficulty shifting, and abnormal pedal behavior.
How to Troubleshoot a Clutch Pedal Sticking to the Floor
Clutch pedals in manual cars stay on the floor if there's a failed clutch release bearing, slave cylinder, clutch master cylinder, or clutch linkage.