Quot;change oil" message has been coming on the last 6 mo...


Quot;change oil" message has been coming on the last 6 months, even if oil has been changed. Now the red oil icon has been coming on. How can I tell if it's a faulty sensor or a failing oil pump? Mechanic's Assistant: Whic...

Quot;change oil" message has been coming on the last 6 months, even if oil has been changed. Now the red oil icon has been coming on. How can I tell if it's a faulty sensor or a failing oil pump? Mechanic's Assistant: Which particular sensor are you asking about? And have any trouble codes been triggered? Change oil sensor. No trouble codes, except "change oil" still comes up once in a while. I have no check engine code, but the red oil icon scares me. Mechanic's Assistant: What is the make/model/year of your car? 2008 jeep renegade Mechanic's Assistant: Are you fixing your Renegade yourself? What have you tried so far? I haven't done anything but make sure my oil is clean and up to safe level. Mechanic's Assistant: Anything else you want the Mechanic to know before I connect you? I think that covers it

Automotive Expert
Hello and welcome to JustAnswer, my name is \*\*\*\*\* \*\*\*\*\* I have over 22 years of experience in this field. I'm so sorry for your inconvenience and hopefully, I can help. You need to reset the oil life message. To do this follow these steps. 1. Turn the ignition to the ON position. Do not start. 2. Press the accelerator to the floor 3 times within 10 seconds. 3. Turn the ignition OFF 4.Turn the ignition to the ON position again and now the light should be OFF.

What others are asking

How do I know if the occupant restraint controller (ORC) is working?
The occupant restraint controller (OCR) is what monitors the sensors detecting a crash, and is what sends the signal to deploy the air bags. This is a passive system, which means, it's working whenever the key is in the "Run"...
Car makes noise, automatic window switch, and wiper fluid sprayer not working
A car can make a wide variety of noises for a wide variety of reasons, especially under load, so I would recommend having the vehicle driven by a knowledgable technician so that a conclusive diagnosis of the noise (https://www.yourmechanic.com/services/car-is-making-a-noise-inspection) can...
Clutch bite point high with juddering on a 2003 Polo 1.4 TDI
Your clutch is just wearing out. When they start to bite high like that, and start to shutter, your pressure plate and disc are just starting to wear. So my advice is to go and get a clutch job done....
Small rock cracks windshield while driving on the interstate
Hi! Yes it's very possible to have an aftermarket windshield (https://www.yourmechanic.com/article/how-to-get-the-best-price-on-a-windshield-replacement-by-brady-klopfer) installed in your car, though you should make sure to verify with the glass installer that it is still a quality windshield. Often times aftermarket parts can be very...
What do you call the plastic water tank fitted on the sides of the radiator.
This water filled plastic tank is sometimes referred to as an overflow tank, an expansion tank, or a reservoir. The expansion tank is a vessel that is designed to allow anti-freeze and air that are inside your coolant system to...
My RPMs keep going up and down irregularly
Engine surging (https://www.yourmechanic.com/services/car-jerks-forward-at-high-speeds-inspection) can be caused by several issues. Typically in diagnosing these types of issues, you want to start by having your engine scanned for diagnostic troubleshooting codes. If scanning the computer doesn't pull any codes, the best way...
hard to start at morning after a long cranking it will get start but idiling is very rough
Hello. Thank you for writing in. There are several components that may cause a hard-start (https://www.yourmechanic.com/services/car-is-hard-to-start-inspection). First we need to determine if the engine is cranking at a normal speed, and it is taking a while for the engine to...
Car cut off while driving and won't start.
Hi there. It sounds like the throttle position sensor or the throttle pedal position sensor is not working properly. Check both the sensors harnesses and make sure that they are plugged in. Look for any broken wires or corrosion. If...
I have an evap system issue with a check engine light code P0456 for a "really small leak"
Hi there. Unless you have professional EVAP system leak detection equipment, there really isn't much more you can do to isolate or diagnose the source of your EVAP leak or warning light. The one thing we can suggest is to...