Q: I have a lighting bolt icon on my dashboard

asked by on June 27, 2016

I had a cracked raditor which was replaced..and my car later on in the day was unsure if it was gonna overheat or not so when it finally went on the H.on the thermoter my car shut down so i let it rest for 30 minutes then it started back up then i let it sit over night.This morning when i started it the check engine light came on then the lighting bolt popped on

My car has 90000 miles.
My car has an automatic transmission.

Warning Light is on Inspection $94.99 - $114.99 Get a Quote

Hello. The lightning bolt symbol on a Dodge vehicle illuminates when the computer detects an issue with the vehicle’s electronic throttle control. Modern vehicles use electronically controlled throttle bodies to control the amount of air that enters the engine.

If the throttle body or its circuit have any problems it can cause the vehicle to experience drivability issues such as the ones you are experiencing.

A faulty electronic throttle body may cause the vehicle to stall, hesitate on acceleration, and in some cases may even render the vehicle undrivable. I would recommend having the computer scanned for trouble codes to see if any other issues may be present. If you need help with this, a technician from YourMechanic can come to your home or office to diagnose the warning light and any other potential issues you may be having with the car.

The statements expressed above are only for informational purposes and should be independently verified. Please see our terms of service for more details

Get an instant quote for your car

Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing


Experienced Mechanic?

Earn up to $70/hr

What others are asking

How do you manually adjust the driver’s seat?
If your Accord has manual adjusting front seats, you have many of the same controls as on a power model with only a few minor exceptions. Bar: At the front bottom of the seat is a bar. Pull it up...
What does the “Tire pressure sensor fault” warning mean in the message center?
There are several different components for your Tire Pressure Monitoring system and they all must work together to provide you with accurate information. If you see a warning that says, “Tire pressure sensor fault” in the message center of your...
Problems with alarm
If you now have a key that fits the door you will have to hook up all the wires back to normal. After this is done, disconnect the battery and wait at least ten minutes. With all of the doors...
Tires and rims keep getting damaged
Hello. There could be a problem with the suspension on your car. The control arm (https://www.yourmechanic.com/services/control-arm-assembly-replacement), ball joint (https://www.yourmechanic.com/services/ball-joint-front-replacement), and inner or outer tie rod could be damaged. This will cause excessive wear on the tires (https://www.yourmechanic.com/services/excessive-wear-on-outer-edges-of-tire-inspection). There could also...
E-brake adjust.
Hello. These are two separate issues as the brake pedal is a hydraulic system operating with brake pads and rotors and the e-brake is a brake cable that leads to a brake drum assembly. First, lets address the brake pedal...
Car will crank but no start... Fuel pump not coming on. New pump, relay, etc. Will start when hot wire runs from pump wires to bat
There are a couple of approaches to take here - either start from the battery (https://www.yourmechanic.com/services/battery-replacement) and work "towards" the fuel pump (https://www.yourmechanic.com/services/fuel-pump-replacement), fuse box, ignition switch (https://www.yourmechanic.com/services/ignition-switch-replacement), fuel pump relay (https://www.yourmechanic.com/services/fuel-pump-relay-replacement), and wiring connections in between. Or, as you...
If I change spark plugs and wires do I change the rotor and distributor cap also?
It is recommended to replace distributor cap and rotor (https://www.yourmechanic.com/services/distributor-rotor-and-cap-replacement) at the same time you are having the spark plugs and spark plug wires replaced. The cap and rotor contacts will wear down just like the spark plug electrodes wear...
Misfire in cylinder #4
You should be fine to drive for a day or two with a misfire on one cylinder, however I would not recommend letting this go un-repaired as this is something will only get worse and may trigger additional problems and...
door lock problem
Hi there: Based on your question and the information listed, it's possible that you've got an exposed wire somewhere in your vehicle that is causing a short with your door locking mechanism. Sometimes this issue is caused by a faulty...

Related articles

P0146 OBD-II Trouble Code: O2 Sensor Circuit No Activity Detected (Bank 1, Sensor 3)
P0146 P0146 code definition O2 Sensor Circuit No Activity Detected (Bank 1 Sensor 3) What the P0146 code means P0146 is the OBD-II generic code indicating the O2 sensor for bank 1 sensor 3 fails to have a voltage change...
P2253 OBD-II Trouble Code: O2 (Oxygen) Sensor Negative Current Control Circuit High Bank1 Sensor 1
P2253 P2253 code definition O2 (Oxygen) Sensor Negative Current Control Circuit High Bank1 Sensor 1 What the P2253 code means P2253 is a generic OBD2 diagnostic trouble code (DTC) (https://www.yourmechanic.com/article/what-is-the-on-board-diagnostics-obd-system) indicating a fault with the bank 1 sensor 1 O2...
P3468 OBD-11 Trouble Code: Cylinder 9 Deactivation/Intake Valve Control Circuit High
What What the P3468 code means This code indicates that there is a problem with the intake valve on cylinder number 9. When your vehicle’s powertrain control module (PCM) notices that the measured values of the mass airflow sensor, the...