Q: i have a 50 cc scooter the engine won't start after i mess around with the idle
i was trying to stop my scooter from stalling at low speed but while i was tuning the idle it just stop working i was adjusting the air to fuel screw and it stop i tried to put it back where it was at first but nothing try to remove the spark plug and cleaning it but still no result i check the spark plug for a spark and it dose a nice big spark i did notist that my spark plug was very wet tho well that it
It is possible that you could have flooded the carb when you adjusted the air/fuel screw. I would keep the screw where it is at and let the scooter sit for a while to let the fuel disperse. Once the scooter has sat for a while, keep trying to start it and it should start up as long as the screw is adjusted to the same location that it was in the last time it was running correctly.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
Bad clutch safety switch or starter.
Hello, the only way to diagnose this no start concern is with a DVOM. Power needs to be checked starting at the starter motor, 12v at the big wire going to the starter and 12v at the smaller wire at...
Noises starting while turning on 2006 Pontiac Solstice
The fluid in the rear end can be inspected for extensive wear on the gears inside and the drive shaft joints for any amount of play. Check all of the vehicles fluids to make sure they are full and clean...
Tire rotation for all-wheel drive and low profile tires - 2015 Infiniti Q50 Sport
Hello. The recommendation for tire rotation (https://www.yourmechanic.com/services/rotate-tires) is every 7,500 miles. I would simply rotate them at every oil change (https://www.yourmechanic.com/services/change-oil-and-filter). Being that it is all-wheel drive (https://www.yourmechanic.com/article/how-all-wheel-drive-works), you need to keep up on this as you do not want...
wheel hot to touch and smell like something is burning
Hi there: In most cases, this is a sign of a dragging emergency brake, faulty brake pressure issue or wheel bearings that are damaged. If you jack up the rear of the vehicle and your wheel spins freely, then it...
Unusual noise after locking my car remotely
Hello there. Unfortunately, we are unable to offer you ideas as we don't see too many Holden vehicles here in the United States. We are only able to offer service and repair suggestions for cars, trucks and SUV's that are...
My car will start up. But died after 30 seconds. Then it won't start again unless I wait 20 to 30 mins
This may be a sign of a faulty ignition coil. Ignition coils (https://www.yourmechanic.com/services/ignition-coil-replacement) are coated with a varnish-like insulation that becomes brittle over time after being stretched then contracted repeatedly. The insulation develops small fractures that open when heated and...
4l60e transmission runs fine until engine warms up then loss of all gears and metal on metal noise from bell housing. What do I do
Hi Mike. Anytime you hear metal to metal coming from inside the bell housing of an automatic transmission, that's typically an indication of damage to the torque converter or flywheel. With 300,000+ miles on your Silverado, it's probably time to...
How clean the throttle body cleaning...and reset the M.I.L an
Spray on solvents are used to clean the throttle body. These are widely available at auto parts stores and many household goods retailers. However, prior to cleaning the throttle body, the reason that the check engine light has come on...
What is the right way to install the rear main seal?
Hi Justin. Thanks for contacting us today. If you are replacing the rear seal, you really should purchase a service and repair manual for your Ford F-150, as following each step in the right order is crucial to ensure a...
Related articles
Symptoms of a Bad or Failing Crankshaft Position Sensor
Common signs of a faulty crankshaft position sensor include issues starting the vehicle, intermittent stalling, and the Check Engine Light coming on.
Symptoms of a Bad or Failing Idle Control Valve
Common signs include irregular or unusually high idle speed, the Check Engine Light coming on, and stalling while idling.
How to Re-Start Your Second Generation Prius
Nobody Nobody wants their car to suddenly stop working. Unfortunately, Toyota recalled around 75,000 of their 2004 Prius cars because of some technical issues that were causing them to stall. This could be caused by several different failures in the...
Browse other content
Cities
Estimates
Maintenance