Q: I'm getting code po171 lean bank 1.
I replaced 02 sensor bank 1 sensor 1,fuel filter,air filter,pcv,mass air spark plugs,replaced intake gasket . Truck ran go for about 20 miles then started to run rough no power.running same way before all new parts installed.
My car has 20500 miles.
My car has an automatic transmission.
Recommended Services
| Check Engine Light is on Inspection | $94.99 - $114.99 | Get a Quote |
There vehicles are known for the intake manifold warping and having fuel injector problems at higher miles. The fuel trims can be checked while the engine is warm and spraying around the intake manifold gaskets to see if the trims jump around once brake cleaner or starting fluid is sprayed around the seals. Consider hiring an experienced technician equipped with a professional scan tool like one from YourMechanic who can come out and run a few tests on your lean condition to offer a more personal diagnosis.
The statements expressed above are only for informational purposes and should be independently verified. Please see our
terms of service
for more details
Get an instant quote for your car
Our certified mechanics come to you ・Backed by 12-month, 12,000-mile guarantee・Fair and transparent pricing
What others are asking
What does the Low Tire Pressure Light on the dash mean?
The Low Tire Pressure Light in the dash of your car comes on when the tire pressure monitoring system detects a tire low on air. However, it can also come on for other reasons as well. Here’s what you should...
Battery draining constantly.
The first thing to do is to make sure that your friend did not leave any bare wires that are touching ground and shorting out. If the wiring is ok then the problem may just be that it started to...
AC/heater not blowing on high.
Having your AC and Heater make a humming noise while running on high can be an annoying occurrence while you are trying to enjoy driving your truck. Since the problem is persisting after replacing the blower motor resistor, there are...
Engine turns over, cannot run
Hello. I would have the system scanned for any codes (https://www.yourmechanic.com/article/how-to-read-and-understand-check-engine-light-codes-by-jason-unrau) and have them diagnosed to see if they lead to possible cause of the problem. Have the fuel system also checked for any problems when the problem happens to...
How much can I expect to pay in maintenance to cost over the next 5 years?
Hi, thanks for writing in. I'd be happy to provide my insight. Unfortunately, as you may know every car depreciates in value fairly rapidly relative to the amount you have paid for it. As with any car, the dependability is...
High and fluctuating idle. Tried some re-learn programs with no success.
A high an fluctuating idle is usually cause by a vacuum leak or stuck open EGR valve. Also on this vehicle I have seen the PCV valve broken where a failed attempt to remove it from the valve cover it...
Where is the crankshaft position sensor location?
The crankshaft position sensor is located on the driver side of the engine and in the back by the transmission on the engine. If you need further assistance with your crankshaft position sensor (https://www.yourmechanic.com/services/crankshaft-position-sensor-replacement), then seek out a professional, such...
I have a 2001 BMW 325i. It overheated, engine shut down. When cooled down (24 hours), while water poured in the reservoir I could
I'm not clear on where you see your leak, but if it is in the radiator tank itself, that will mean you at least need a radiator. If the car ran hot until it shut off, there may have been...
MAP sensor or something else?
I would recommend using a service such as All data, Mitchell ProDemand, or a Chilton book. The sources may give you the correct testing procedure for the map sensor. By using these test procedures you can be certain that the...
Related articles
P2018 OBD-II Trouble Code: Throttle Actuator Control Module Performance
P2108 P2108 code definition Throttle actuator control module performance What the P2108 code means This trouble code indicates that the powertrain control module has detected a malfunction with the throttle body control motor or module. This code is only found...
P2253 OBD-II Trouble Code: O2 (Oxygen) Sensor Negative Current Control Circuit High Bank1 Sensor 1
P2253 P2253 code definition O2 (Oxygen) Sensor Negative Current Control Circuit High Bank1 Sensor 1 What the P2253 code means P2253 is a generic OBD2 diagnostic trouble code (DTC) (https://www.yourmechanic.com/article/what-is-the-on-board-diagnostics-obd-system) indicating a fault with the bank 1 sensor 1 O2...
P0811 OBD-II Trouble Code: Excessive Clutch Slippage
P0811 means there is either an issue with the clutch position sensor circuit (manual) or the PCM (automatic) often due too faulty, wiring or switches.
Browse other content
Cities
Services