P0175 system rich bank 2


P0175 system rich bank 2 Mechanic's Assistant: What is the make/model/year of your car? 2019 Ford Mustang Mechanic's Assistant: Are you fixing your Mustang yourself? What have you tried so far? Cleaning the air f...

P0175 system rich bank 2 Mechanic's Assistant: What is the make/model/year of your car? 2019 Ford Mustang Mechanic's Assistant: Are you fixing your Mustang yourself? What have you tried so far? Cleaning the air filter and mass air flow sensor Mechanic's Assistant: Does the [engine](/topics-engine-ford/) stall right after starting? And what about hesitation or jerking during acceleration? No stalling or hesitation with acceleration

Automotive Expert
Welcome to JustAnswer Mechanical Support! I am AutoExpert20 and I will be Investigating and Supporting your question today. I understand it can be really frustrating when your auto is not working an expected but don't worry as I am here to help! I may need further information, however, if required I will let you know! Hi, the most common problem for a rich bank 2 fault code is normally one of the most common cause for the P0175 code to be thrown is a vacuum leak. Take a look around and see if you can find the vacuum leak, but it also could be a miss fire faulty or worn [spark plug](/topics-spark-plug-ford/).

What others are asking

Transmission problems
It sounds like the transmission is mechanically sound if you are experiencing no slippage. You will want to have the transmission fault codes (https://www.yourmechanic.com/article/the-most-common-error-codes-for-transmission-problems) read out to see if there are any issues that could be inhibiting the shifts. Other...
Top radiator hose is cold while the lower is hot
You may be correct that the thermostat is stuck closed. One way to test a thermostat (https://www.yourmechanic.com/article/symptoms-of-a-bad-or-failing-thermostat) is to put it in a pot of water and bring the water temperature up to the thermostat opening temperature. This is imprinted...
Erratic RPMs, 1995 BMW 318is
Hello there, there are a few possible causes for your 1995 BMW 318is to have a fluctuation in the RPM's. The most common are a vacuum leak (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-a-vacuum-leak), oxygen sensor (https://www.yourmechanic.com/services/oxygen-sensor-replacement), throttle sensor (https://www.yourmechanic.com/services/throttle-position-sensor-replacement), exhaust leak (https://www.yourmechanic.com/article/is-it-safe-to-drive-with-an-exhaust-leak), or the fuel...
Starting - 2004 Toyota Vitz
Hello. If the issue started after you changed the battery, then it may be possible that you need to reprogram the remote or that it may be defective. If it is an OEM push to start system, you may need...
I keep getting a cylinder 3 misfire code P0303. I have replaced the spark plugs and ignition coils and have had no luck.
Hello There, You may want to try checking things like mass air flow sensor, fuel pressure, injector connections/pulses, etc. Often times, when these components are not working properly or causing a lean fuel condition, this may cause a misfire due...
Electric power steering replacement how much does it cost
From the description you have provided it sounds like it could be, the electric power steering motor has failed. It could also be, an electrical power or ground failure to the power steering motor. Before you have the electric steering...
My car when accelerating feels like it get stuck this also happens when I turn. What could this be?
Hi there. I am not quite sure what you mean in regards to "getting stuck" when you accelerate. If you are indicating that the vehicle has difficulty accelerating like it usually would, it's possible that the issue is caused by...
Car brakes are stuck on.
Try putting the transmission shifter in park or neutral and see if the brake pedal becomes unstuck. If not, then you may have to remove the battery cables to reset the electrical system so that the parking assist is shut...
What can happen if incorrect parts are installed on a vehicle?
To answer your question about safety, I would have to know exactly which brake components are not correct and the part numbers of the incorrect parts that were installed. If the stabilizer bar bushings installed on your vehicle are not...