I’ve taken my VF CalaisV LS2 to Autolec three times first...
Responses
Gary
253 days ago
Hello! My name is Gary.
Welcome to JustAnswer.
I'm reviewing your question now, and will post back with a reply shortly.
Your Holden dealer sent you to an Auto Electrician?
You need to find another Holden dealer with better qualified techs with Holden training.
What is this "EBC" computer, do you mean the EBCM?
What displays on the dash, when you say engine light on?
More than likely a wiring fault with the oil level sensor circuit.
And this is oil level, not oil pressure, correct?
The LS engine oil pump is prone to the oil pump relief valve sticking open.
So we need a new scan for codes please.
Gary
Customer
253 days ago
I’ve had it scanned four times and comes up same every time oil censer
Gary
253 days ago
Oil LEVEL, or oil PRESSURE?
What is the code number please, eg P0522?
Gary
Customer
253 days ago
I don’t noThey have replaced the oil censer module four times
Gary
253 days ago
Why don't they tell you this number, if you had it scanned 4 times?
Do they just clear it out, and not tell you anything?
Why keep replacing the oil level sensor?
Obviously a wiring fault, my bet is a poor crimp in terminal at the sensor connector.
Gary
Customer
253 days ago
Tested all terminals and there all fineI clicked call you but nothing happened
Gary
253 days ago
Sorry, I haven't seen a phone call request, but we can certainly have a chat if you like.
Please make the call request, and the system should notify me first, before it becomes available to other techs.
Gary
Gary
253 days ago
Good morning,
I hope my advice has been of assistance to you.
Kind regards.
Gary
Still not sure what you need?
Have a certified mobile mechanic diagnose what's wrong with your car, at your home or office.
Top Questions
Trending Topics
What others are asking
Check engine light is always on, what can I do?
The evaporative emissions system on the Kia Soul is susceptible in warm climates or times of the year when spiders nest in the evaporative vent system, causing the check engine light to randomly come on. When the system is tested,...
Electronics not working after leak
Depending on the severity of the leak that your vehicle had can help determine how much damage occurred from the leak. If any of the wiring was exposed to the water from the leak it could have caused corrosion or...
Engine over-heating and Radiator then overflows fluid or steam.
First of all, overheating the engine will damage it. The list of reasons why is long, but here is a partial list of reasons why overheating the engine will ruin it. The engine oil becomes much thinner at higher temps....
Rumbling noise upon acceleration
Hello. I believe the circumstance you are experiencing is from a worn component in the rear end, such as a bad wheel bearing (https://www.yourmechanic.com/services/wheel-bearings-replacement) or axle (https://www.yourmechanic.com/services/axle-cv-shaft-assembly-replacement). I suggest that you have the rear end of the truck evaluated by...
Bad car thermostat
Hi there. The heating control valve (https://www.yourmechanic.com/services/heater-control-valve-replacement) or thermostat is responsible for sending recently heated coolant from the cooling tubes and to your heater core. As long as you keep your heater turned "off", it shouldn't impact the operation of...
Car still won't start even after replacing battery and checking fuses
If I am reading your symptom description correctly, the engine died at speed, the Check Engine light came on, and the engine now turns over but won't actually start despite a new battery. First item to check are the codes...
Car won't start - 2003 Ford Focus
Hello. Unless the timing belt suddenly broke, which would have resulted in stalling of the engine as well as a noticeable sound from the engine, it is not likely a timing issue. If the fuel pump has power and is...
Why would I still have a check engine light after my camshaft and crankshaft sensors were replaced 2008 Kia Sedona
If you are continuing to get the same codes after these sensors were replaced then you more than likely have a worn out timing belt. When the belt is worn then the sensors will not read correctly. If you want...
Car overheating 2006 Infiniti M35
Hello - the fact that your car maintains a steady temperature near design temp (center of the gauge), suggests the thermostat is working properly. Overheating while idling or at low speeds (https://www.yourmechanic.com/question/vehicle-is-starting-to-overheat-at-idle-by-dustin-p) is usually a problem with a clogged radiator,...
Browse other content
Cities
Services
I’ve taken my VF CalaisV LS2 to Autolec three times first changed ebc computer and then engine light came on again so took back and said oil censer relplace so they did two hours later engine light came on took back said oil cense...
I’ve taken my VF CalaisV LS2 to Autolec three times first changed ebc computer and then engine light came on again so took back and said oil censer relplace so they did two hours later engine light came on took back said oil censer again so replaced and again engine light came on said same problem they said the new oil Censer was faulty so replaced it and now it’s back on again what should I do Mechanic's Assistant: Has your vehicle stalled? Has anyone run a diagnostic test to pull the trouble code? No never stalled and I took it for a four hour drive at 110km and no problem with anything not even temp yes has had diagnostic on and says same thing all the time oil censer Mechanic's Assistant: What year is your Calais? 2013 Mechanic's Assistant: Are you fixing your Calais yourself? What have you tried so far? No I’ve taken it to a Holden dealership and they sent me to an Autolec the only thing I’ve done is disconnected the positive lead on battery and left of for hour and put on and engine light was of but after driving for about an hour came back on